DigiSender Zentrum Control DG420 Manual de instruções - Página 2

Procurar online ou descarregar pdf Manual de instruções para Transmissor DigiSender Zentrum Control DG420. DigiSender Zentrum Control DG420 10 páginas.

Imprimir página
DG420 DigiSender Control Zentrum
Table of Contents
Page 3
Introduction
SECTION 1: Installation Guide
Page 4,5
Unpacking your DigiSender™ Control Zentrum™
Page 6,7
Panel Descriptions
Page 8,9
Connecting the transmitter
Page 10
Configuring the remote control extender
Page 11
Connecting the receiver
SECTION 2: Daily Usage
Page 12
Controlling your main television source
Page 13
Controlling your second television source
Page 14
Recording Satellite/Cable, DVD or Camcorder on your VCR
Page 15
Recording Satellite/Cable, VCR or Camcorder on your DVDR
SECTION 3: Additional Information
Page 16
Expand your Zentrum system
Page 17
Advanced Configuration
Page 18
Technical Support
Page 19
Frequently asked questions
This device is liable to receive interference signals generated by Spread
Spectrum Lan networks and stray microwave emission from some
Microwave Ovens. Such interference will cease after the interfering
Page 2
WARNING
To prevent damage do
not expose this unit to
rain or moisture.
INTERFERENCE WARNING
equipment has been switched off.
Online Support at www.digisender.net
FAQ
Q:
I can only see a fuzzy or 'snowstorm effect on screen
A:
This could be caused by a number of reasons. Check out the following...
i) Your receiving television is set to the correct A/V channel (see page 15 for details).
To confirm this, switch off your receiver. If the screen does not go black, you haven't selected the A/V
channel. You may need to refer to your television instruction guide for details.
ii) The correct DigiSender Audio/Video channel has been correctly set. The same audio/video channel
must be selected on both the transmitter and receiver. See page 17 for details.
Q:
There is interference on my picture!
A:
You need to change the Audio/Video channel of your DigiSender. See page 17 for details.
Q:
I can't choose a different Satellite/Cable channel from my main room!
A:
This is normal. Your Satellite/Cable decoder can only decode one channel at a time.
Q:
My DigiSender remote control has stopped working
A:
You need to replace the remote control batteries. It takes a CR2025 battery, available from most electrical
outlets. Some electrical equipment may interfere with the remote controls operation. Move the
DigiSender transmitter and receiver away from other electrical devices and keep cables neat and tidy.
Q:
My DigiSender remote control won't change my Satellite/Cable channel!
A:
The DigiSender Remote Control is designed for changing the input device and/or Audio/Video channel.
It will not operate any satellite or cable systems. You need to use your original satellite/cable remote
control.
Q:
My neighbour is changing my Satellite/Cable channel!
A:
You need to change the Remote Control Extender channel of your DigiSender. See page 17 for details.
Q:
I can't get my Satellite/Cable/DVD/VCR remote control to work in the second room!
A:
This could be a number of things...
i) Check the position of the magic eye as shown on page 13. Try moving the eye into different positions.
ii) Change the batteries in your remote control.
iii) Try moving the DigiSender transmitter and receiver away from electrical equipment that may be
interfering.
Q:
I can't get my Digital Cable remote control to work!
A:
This model of DigiSender is fully compatible with both RC5 and IrDA active digital receivers, but you may
need to follow these additional steps...
i) The remote control (IrDA) range is slightly lower than for other RC5 devices. Make sure you are using
your cable remote control within 3m of the DigiSender receiver.
ii) Pay extra attention to positioning the magic eye as close as possible to the IR pickup on your cable
receiver.
Q:
Where can I purchase upgrades and additional parts for my DigiSender?
A:
Always ask at your local stockist. More information is available from the DigiSender website at:
http://www.digisender.net
Q:
How can I connect my receiver to a Hi-Fi or Amplifier?
A:
Use the Phono outputs on the rear of the receiver.
Q:
I am getting interference from my 2.4GHz wireless network, LAN or ADSL Router.
A:
There are 4 available channels for the DigiSender to use (see Page 17). Please consult the documentation
supplied with your network equipment for information on changing the channel configuration.
Please read this instruction manual carefully prior to installation
DG420 DigiSender Control Zentrum
Page 19