Sharp AR-M550U Manual de instruções da chave - Página 16
Procurar online ou descarregar pdf Manual de instruções da chave para Impressora tudo em um Sharp AR-M550U. Sharp AR-M550U 20 páginas. Digital multifunctional system
Também para Sharp AR-M550U: Manual técnico (48 páginas)
Imprimir página
PROGRAMS FOR COPY MODE
This chapter explains the key operator programs that are used for copy mode.
Copy settings
"Copy settings" consists of the following programs:
G Initial status settings
G Exposure adjustment
G Rotation copy setting
G Add or change extra preset ratios
G Initial margin shift setting
G Erase width adjustment
G Card shot settings
*1
G Initial tab copy setting
G Setting a maximum number of copies
G Disabling deletion of job programs
G Disabling of bypass-tray in duplex copy
G Disabling of auto paper selection
*1 Default settings selected with these programs apply
to all functions of the machine (not just the copy
function).
Initial status settings
The copy settings revert to the default settings when
the power switch is turned on, when the [CA] key is
pressed, or when the auto clear time elapses. This
program is used to change the default settings, or
return changed default settings to the initial factory
default settings.
Defaults for the following copy settings can be
changed:
Paper tray/Exposure tray/Copy ratio/2-sided copy/Out
put (sort/non-sort, staple sort/non-staple, output tray)
NOTE
If this program is used to change the default setting
for the duplex function to other than "one-sided"
"one-sided" and the automatic document feeder fails
or is disabled, the setting will revert to "one-sided"
"one-sided".
* DISABLING OF DOCUMENT FEEDER (page 11)
DISABLING OF DUPLEX (page 11)
Exposure adjustment
This program is used to adjust the exposure level when
"Auto" is used for the copy exposure.
The factory setting is "5". "1" indicates lighter density
and "9" indicates darker density on the touch panel.
14
*1
Rotation copy setting
If this program is set, the image of originals will rotate
when the orientation of the originals does not match
that of the copy paper.
(Rotation copy will function only if the auto paper select
or auto image mode has been selected.)
NOTE
For copying from A5 or 5-1/2" x 8-1/2" size originals
onto A5R or 5-1/2" x 8-1/2"R paper, this program
must be set.
Add or change extra preset ratios
When using AB sizes, there are normally five preset
enlargement ratios and five preset reduction ratios.
When using inch sizes, there are normally four preset
enlargement ratios and four preset reduction ratios.
This program allows you to add two more preset
enlargement ratios and two more preset reduction ratios.
This program also allows you to change a preset ratio.
NOTE
Only an added preset ratio can be changed.
Initial margin shift setting
This program is used to set the initial margin shift
amount.
The initial margin shift amount can be set from 0 mm to
20 mm (0" to 1") in increments of 1 mm (1/8").
Normally the margin shift is set to 10 mm (1/2") for both
the front and back of the paper.
Erase width adjustment
This program is used to set the initial width of edge
erase copying.
The edge erase width can be set from 0 mm to 20 mm
(0" to 1") in increments of 1 mm (1/8").
The edge erase and center erase widths are normally
set to 10 mm (1/2").
Card shot settings
This program is used to set the initial original size for
the card shot function.
Enter the X dimension (width) first and then the Y
dimension (length).
Both the X and Y dimensions can be set from 25 mm to
210 mm (1" to 8-1/2") in increments of 1 mm (1/8").