Bitspower Sedna PH518 Manual de instalação - Página 13
Procurar online ou descarregar pdf Manual de instalação para Invólucro Bitspower Sedna PH518. Bitspower Sedna PH518 17 páginas. For phanteks 518-pwm
Também para Bitspower Sedna PH518: Manual de instalação (6 páginas)
Imprimir página
安裝方式1/Installation 1/安裝方式1
請按照正確的順序安裝
Follow the right sequence to install.
请按照正确的顺序安装
安裝方式2/Installation 2/安裝方式2
請按照正確的順序安裝
Follow the right sequence to install.
请按照正确的顺序安装
手轉螺絲不能鎖太緊，彈簧略有壓迫且保有間
隙如下圖。手轉螺絲不能旋轉到底，當鎖太緊
時，SCM3F6螺絲會被帶動，並會被帶離主板
，反而導致冷頭與CPU貼合效果不好。
The thumb screw cannot be locked too tightly,
the spring is slightly pressed and the gap is kept
as shown below. The thumb screw cannot be
rotated to the end. When the spring screws too
tight, the SCM3F6 screw will be driven and will
be taken away from the motherboard, which will
cause the water block and CPU not to be closed
well.
手转螺丝不能锁太紧，弹簧略有压迫且保有间
隙如下图。手转螺丝不能旋转到底，当锁太紧
时，SCM3F6螺丝会被带动，并会被带离主板
，反而导致冷头与CPU贴合效果不好。
注意，跑水前，請先確認所有零件已安裝在正確的位置上，在不開主機，單開水泵的情况下，進行24小時的跑水測試， 確保無漏水情况後再開主機，避免發生漏水而導致電腦零件的損壞。
Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test
with only the pump connected to the power supply .
注意，跑水前，请先确认所有零件已安装在正确的位置上，在不开主机，单开水泵的情况下，进行24小时的跑水测试， 确保无漏水情况后再开主机，避免发生漏水而导致电脑零件的损坏。
本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。
Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.
本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。
Sedna PH518 Kit Set for Phanteks ENTHOO EVOLV X GLASS Case
手轉螺絲/Thumb screw/手转螺絲
彈簧/SPRING/弹簧
1毫米墊片/1mm SPACER/1毫米垫片
冷頭 /CPU Block/ 冷头
孔位固定螺絲 /SCM4M3/ 孔位固定螺丝
手轉螺絲/Thumb screw/手转螺絲
彈簧/SPRING/弹簧
1毫米墊片/1mm SPACER/1毫米垫片
冷頭 /CPU Block/ 冷头
SCM3F6螺絲 /SCM3F6 screw/ SCM3F6螺丝
1毫米墊片/1mm SPACER/1毫米垫片
背板墊片/Back Pad/背板垫片
背膠絕緣片/Paste Pad/背胶绝缘片
金屬背板/Metal Backplane/金属背板
M3x32 毫米 螺絲/M3x32mm SCREW/M3x32毫米螺丝