Samsung 5 Series Manual do utilizador - Página 35

Imprimir página

Listening through a Receiver

You can listen to sound through a receiver (i.e Home Theatre) instead of the TV speaker.

1. Select Receiver and set to On.

2. Press the

EXIT

button to exit.

✎

If your receiver supports audio only, it may not appear in the device list.

✎

The receiver will work when you have properly connected the optical in jack of the receiver to the

OUT (OPTICAL)

jack of the TV.

✎

When the receiver (i.e Home Theatre) is set to On, you can hear sound output from the TV's Optical jack. When the

TV is displaying a DTV (aerial) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a

digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from

the receiver.

✎

NOTE

You can only control Anynet+ devices using the TV remote control, not the buttons on the TV.

The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet

The Anynet+ functions do not operate with other manufacturers' products.

Troubleshooting for Anynet+

Problem

Anynet+ does not work.

I want to start Anynet+.

I want to exit Anynet+.

The message "Connecting to

Anynet+ device..." appears on the

screen.

The Anynet+ device does not play.

The connected device is not

displayed.

The TV programme cannot be

recorded.

The TV sound is not output

through the receiver.

Possible Solution

•

Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.

•

Connect only one receiver (home theatre).

•

Check if the Anynet+ device power cord is properly connected.

•

Check the Anynet+ device's Video/Audio/HDMI Cable connections.

•

Check whether

Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

•

Check whether the TV remote control is in TV mode.

•

Check whether it is Anynet+ exclusive remote control.

•

Anynet+ doesn't work in certain situations. (Searching channels, operating

setup), etc.)

•

When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off

and on again.

•

Check if the Anynet+ Function of Anynet+ device is set on.

•

Check if the Anynet+ device is properly connected to the TV and check if the

On in the Anynet+ Setup menu.

•

Press the

TOOLS

button to display the Anynet+ menu and select a menu you want.

•

Select

View TV in the Anynet+ menu.

•

Press the

SOURCE

button on the TV remote control and select a device other than Anynet+ devices.

•

Press

>/<, PRE-CH, and

when a tuner-embedded Anynet+ device is not connected.)

•

You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.

•

Use the remote control when the Anynet+ setting or switching to view mode is complete.

•

You cannot use the play function when Plug & Play (Initial setup) is in progress.

•

Check whether or not the device supports Anynet+ functions.

•

Check whether or not the HDMI Cable is properly connected.

•

Check whether

Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

•

Search Anynet+ devices again.

•

You can connect an Anynet+ device using the HDMI Cable only. Some HDMI cables may not support Anynet+

functions.

•

If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a power

failure, please repeat the device scan.

•

Check whether the antenna jack on the recording device is properly connected.

•

Connect the optical cable between TV and the receiver.

FAV.CH

to change the TV mode. (Note that the channel button operates only

DIGITAL AUDIO

+ device.

Media Play or Plug & Play (Initial

Anynet+ (HDMI-CEC) is set to

English