Digital Home Systems DHS-SNS-SM-DHS Manual de instalação rápida - Página 2

Procurar online ou descarregar pdf Manual de instalação rápida para Alarme de fumo Digital Home Systems DHS-SNS-SM-DHS. Digital Home Systems DHS-SNS-SM-DHS 2 páginas. Z-wave smoke sensor
Também para Digital Home Systems DHS-SNS-SM-DHS: Manual de instalação rápida (2 páginas)

Imprimir página

Installation

Mounting

Unlock the back bracket.

Use the designated holes on the back bracket to screw mount it in

desired location.

For optimal use, mount the Smoke Sensor on the ceiling.

Place one 9V battery into the Smoke Sensor.

Mount the Smoke Sensor onto the back bracket.

After a few seconds the Smoke Sensor is ready.

Inclusion/exclusion into a Z-Wave network

Network Wide Inclusion method (NWI)

1. When the Smoke Sensor is not yet included in a Z-Wave network, NWI

procedure will start automatically for 120 seconds after powering on the

Smoke Sensor (connecting a battery).

2. Make sure your Z-Wave controller is in the correct operating mode

(inclusion) just before the Smoke Sensor is powered and the inclusion

process will start automatically. Please check the status of inclusion on

your Z-Wave home controller.

Normal include or exclude method

1. Make sure your Z-Wave home controller is in the right operation mode

(include or exclude).

2. Press and hold the push button for 1 second and release to start the

inclusion or exclusion process (indication mode: Ready for learn mode).

Associations

You can add associated security devices to your Smoke Sensor. Press

and hold the push button for more than 5 seconds and release to test

whether the security devices associated with your Smoke Sensor work

properly.

Operation

Manual control

1. When you press the push button, the Smoke Sensor will beep and the

indicator light will blink immediately.

2. Release the push button to clear trigger status.

Smoke Trigger

1. When smoke is detected, the Smoke Sensor will beep and the indicator

light will blink.

2. The Smoke Sensor won't stop beeping unless smoke has disappeared or

the battery is removed for a short while (hardware reset).

Security system test within Z-Wave network

1. To test the sensor connection with your Z-Wave home controller (e.g.

VeraEdge) press and hold the push button for at least 5 seconds until the

indicator is continuously ON for about 1.5 sec.

2. Check if your Z-Wave home controller has seen that the device is

triggered.

3. To remove the triggered status, hold the push button for about half a

second (one or two beeps only).

4. Check if your Z-Wave home controller that the device is in un-triggered

status.

Indication modes

The indicator gives various statuses of the device as follows:

1. Automatically add: blinks 120 seconds.

2. Learn in progress (add): Indicator light blinks 1 time.

3. Learn in progress (remove): Indicator light blinks 1 second (8 times).

4. Learn mode success: Indicator light is on for 1 second.

5. Learn mode failed: Indicator light blinks fast.

Supporting Command Classes

Basic Device Class: BASIC_TYPE_ROUTING_SLAVE

Generic Device Class: GENERIC_TYPE_SENSOR_ALARM

Specific Device Class: SPECIFIC_TYPE_BASIC_ROUTING_SMOKE_SENSOR

Listening: TRUE, Z-Wave Lib: 4.51

Command Classes: 71 85 80 72 30 86 84

Class: 0×71 COMMAND_CLASS_ALARM

Class: 0×85 COMMAND_CLASS_ASSOCIATION

Class: 0×80 COMMAND_CLASS_BATTERY

Class: 0×72 COMMAND_CLASS_MANUFACTURER_SPECIFIC

Class: 0×30 COMMAND_CLASS_SENSOR_BINARY

Class: 0×86 COMMAND_CLASS_VERSION

Class: 0×84 COMMAND_CLASS_WAKE_UP

Troubleshooting

NOTE: Before including the product to your Z-Wave network it is

advised to perform the exclusion procedure to reset network settings.

Frequently Asked Questions

Q: I can't include my Z-Wave Smoke Sensor into my Z-Wave network,

what am I doing wrong?

A1. Check that your home controller is set to inclusion mode.

A2. The Z-Wave Smoke Sensor may already be included in a different

Z-Wave network. Perform the exclusion procedure and then attempt to

include the Z-Wave Smoke Sensor again.

Q: Why doesn't the Z-Wave Smoke Sensor detect any smoke?

A1. The connection between your Z-Wave Smoke Sensor and home

controller may have been broken. Ensure that the smoke sensor is within

range of your home controller or a Z-Wave device capable of acting

as a repeater is added between the smoke sensor and your gateway,

then exclude and re-include the smoke sensor into your Z-Wave

network.

2. The battery is almost empty, try replacing it.

Q: Why does the push button on the Z-Wave Smoke Sensor not work?

A: Check that Z-Wave Smoke Sensor's battery is new and properly

connected.

Q: Why does the indicator light not work?

A: Check that Z-Wave Smoke Sensor's battery is new and properly

connected. The indicator light will not work if there is no power supplied

to the Z-Wave Smoke Sensor.

This device is using a radio signal that passes through walls, windows

and doors. The range can be influenced by local conditions such as

large metal objects, house wiring, concrete, furniture, refrigerators,

microwaves and similar items. On average, the indoor range is

approximately 12- 30 meters.

Do not expose this product to excessive heat or moisture.

Prevent long term exposure to direct sunlight.

Do not attempt to repair this product. If the product is damaged or if

you are in doubt about the proper operation, take the product back

to the place of purchase.

Do not clean the product with any liquid.

Do not paint.