Siemens HB24D.52. Manual de instruções - Página 6
Procurar online ou descarregar pdf Manual de instruções para Forno Siemens HB24D.52.. Siemens HB24D.52. 24 páginas.
Imprimir página
Automatic calibration
The boiling temperature of water depends on the air pressure.
During calibration, the appliance is adapted to the pressure
conditions in the location where it is installed. This happens
automatically when you first use the appliance (see section:
First use). More steam develops than usual.
It is important that the appliance steams without interruption for
20 minutes at 100 °C. Do not open the appliance door during
this time.
If the appliance was not able to calibrate itself automatically (for
example, because the appliance door was opened), the
Before using for the first time
In this section you will find out which steps are required before
using the appliance for the first time:
Setting the clock
■
Setting the water hardness range
■
Starting the appliance for the first time
■
Cleaning the accessories before use
■
Setting the clock
After the power has been connected, the
light up in the display. Set the clock.
Press the
button.
0
1.
The time
:
is shown in the display.
‚ƒ
‹‹
Use the
or
button to set the clock.
@
A
2.
After a few seconds, the time which has been set is applied.
Setting the water hardness range
Descale your appliance regularly. This is the only way to
prevent damage.
Your appliance automatically displays when it needs descaling.
It has been preset to water hardness range "medium". Change
the value if your water is softer or harder.
You can check the water hardness with the test strips supplied
or ask your water supplier.
If your water is very hard, we recommend that you use softened
water.
You can only dispense with descaling completely if you
exclusively use softened water. If this is the case, change the
water hardness to "softened".
You can change the water hardness range in the basic settings
when the appliance is switched off.
If required, turn the operating mode selector to
1.
the appliance.
Press and hold the
button until
0
2.
display.
Press the
0
button repeatedly until
3.
("moderate" water hardness range).
Press the
or
button to change the water hardness range.
@
A
4.
Possible values:
softened
™† ‹
soft
™† ‚
moderate
™† ƒ
hard
™† „
very hard
™† ...
Press and hold the
button to exit basic settings.
0
5.
The change is saved.
6
symbol and
:
0
‹
‹‹
to switch off
Û
appears in the
™‹ ƒ
™† ƒ
appears
-
I
II
III
IV
calibration process is carried out again during the next cooking
operation.
After moving house
So that the appliance automatically adjusts itself to its new
location, you must reset the appliance to the factory settings
(see section: Basic settings) and repeat the initial start-up
process (see section: First use).
After a power cut
The appliance saves the calibration settings even in the event
of a power cut or disconnection from the mains. Recalibration
is not necessary.
First use
Before first use, heat the empty appliance for 20 minutes to
100 °C using
é
Steam. Do not open the appliance door
during this time. The appliance is automatically calibrated (see
section: Automatic calibration).
Fill and insert the water tank (see section: Filling the water
1.
tank).
Before using for the first time, moisten the seal in the tank
cover with a little water.
Turn the operating mode selector to
2.
Turn the temperature selector to 100 °C.
3.
Press the
button.
†
4.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and a signal
sounds.
To switch off the appliance, turn the operating mode and
5.
temperature selectors to
Leave the appliance door ajar until the appliance has cooled
down.
Cleaning the accessories before use
Using soapy water and a soft cloth, clean the accessories
thoroughly before first use.
é
Steam.
Û
.