EPSON PowerLite 8300i Projector
Controlling Multiple Projectors
If you're using more than one projector, you can control all
the projectors—or just selected ones—by using the projector
ID system. To operate a projector, you have to set the remote
control's ID to match that of the projector. Or you can
control all of the projectors simultaneously by setting the
remote control's ID to zero.
Setting the Projector ID
The projector's default ID is 1. If you need to change it,
follow these steps:
1. Access the projector's
Advanced2
.
Projector ID
Video
Video
Audio
udio
Effect
Eff
ect
Setting
Setting
User's Logo
User's Logo
Adv
Advanced1
anced1
Advanced2
Adv
anced2
About
About
Reset All
Reset All
[ ESC ]: Return
[
/
]: Select
2. Press the right or left side of the
remote control to increase or decrease the ID value.
3. Press
to set the value.
Enter
4. When done, press
ESC
Setting the Remote Control ID
The remote control's default ID is zero. If you need to change
it, follow these steps:
1. Press the
button on the remote control.
ID
You see it light up.
2. Press one of the numbered buttons on the
remote control to select the desired ID (0
through 9). Select zero to control all
projectors, or select a number to match the
ID of the projector(s) you want to operate.
The
button's light shuts off and the new ID is registered.
ID
If you would like to check the remote control's current ID,
press the
button twice in succession. Count the number of
ID
flashes; this number corresponds to the remote control's ID.
12
EPSON PowerLite 8300i Projector
-
menu and highlight
:
Br Brightness Control
ightness Control
High
High
Low
: 1
Setting
Projector ID
Projector ID
Netw
Network
Setting
COM P
COM Port
:
RS-232C
RS-232C
USB
USB
:
BNC Sync Termination
BNC Sync
mination
Color Temp
Color
ON
ON OFF
emp.
OFF
RGB
RGB
Reset
Reset
Execute
[
]: Set
[Menu]: Exit
pointer button on the
to exit the menu system.
Nine
Zero
0
Managing Projectors from a Remote
Computer
The EasyManagement software lets you monitor and control
projector(s) from a remote computer. These features are
intended for use by network administrators.
Use EMP Monitor to see your projectors' status, switch
image sources, and control basic settings.
Use EMP NetworkManager to receive e-mail notifications
alerting you to possible problems.
Make sure you install the software (included on the projector's
CD-ROM) on the computer you want to use to monitor your
projectors.
Setting Up the Network
Connect each projector you want to monitor to your network
and configure it with an appropriate IP address.
1. Connect the projector to your network using a
commercially available 100baseTX or 10baseT network
cable.
Ethernet port
To network port
2. Turn on the projector.
3. Press the
button on the remote control and select
Menu
from the
Network
Video
Br Brightness Control
Audio
Projector ID
Projector ID
Effect
Netw
Networ ork
Setting
COM P
COM Port
User's Logo
Auto setup
Advanced1
BNC Sync Termination
BNC Sync
Advanced2
Reset
Reset
About
Reset All
[
]: Select
[
]: Enter
4. If your network assigns addresses automatically, turn on
.
DHCP
5/03
menu.
Advanced2
:
ightness Control
High
High
Lo
Low
: 1
Set
Set
Set
Set
:
RS-232C
RS-232C
USB
USB
:
uto setup
ON
ON OFF
OFF
:
mination
ON
ON OFF
OFF
Ex
Execute
ecute
[Menu]: Exit
Select
Network
Imprimir página