Cisco Profile Series Folha de instalação

Procurar online ou descarregar pdf Folha de instalação para Sistema de conferência Cisco Profile Series. Cisco Profile Series 2 páginas. Jbod on the 12g sas modular raid controller
Também para Cisco Profile Series: Manual de iniciação (41 páginas), Manual do utilizador (44 páginas), Manual do utilizador (7 páginas), Manual de iniciação (35 páginas), Manual de referência rápida (2 páginas), Manual de instalação (44 páginas), Manual de configuração (13 páginas), Manual de instalação (2 páginas), Manual de início rápido (4 páginas), Manual de início rápido (4 páginas), Manual de instalação (16 páginas), Manual de iniciação (32 páginas), Manual (16 páginas), Manual de iniciação (42 páginas), Manual de iniciação (46 páginas)

Imprimir página

Installing Cisco TelePresence System Profile 42"/52"

Profile 42"/52" contains:

Monitor

Bottom module:

• Column

• Foot module (stand-alone, wheelbase

or wall mounting)

Front grille (inside foot module box)

Speaker grille (inside monitor box)

Camera

Microphones, 2 or 3 pcs.

Touch Screen CS

Remote control

Cables, screws and tools

Cleaning cloth

Unpacking and assembling Profile 42"/52"

Unpack the foot module (stand-alone, wall mounting or wheelbase)

Open the snap lockers.

Lift out the foot module box.

Open the box and unpack the

foot module.

Foot module box

The foot module box contains:

• Foot module (stand-alone, wall

• Four M8×30 screws (wheelbase

mounting or wheelbase)

only)

• Front grille (not for wheelbase)

• Wall brackets and four M6×10

screws (wall mounting only)

• Four M8×50 screws (not for

wheelbase)

A + B:

Mounting the stand-alone or the wall mounting foot modules

to complete the bottom module

CAUTION:

You need two persons to mount the column

to the foot module. Take care to hold the modules firmly

during installation.

Unpack the column. Hold it firmly while moving the foot

module towards the bottom of the column, aligning the

holes for the screws.

Fasten the four M8×50 screws with the

Allen key.

Raise the bottom module.

Rev. Date

Prep.

Checked Change

A Stand-alone foot module (55 lb /25 kg)

HEAVY

CAUTION

Lift out to open

the snap lockers

Wall mounting foot module

Wheelbase foot module

• Allen key

• Torx key (not for wheelbase)

• Level adjustment tool, orange

(stand-alone only)

Fastening the front grille

The front grille is attached using one M6×16 screw (upper

screw) and one M6×10 screw (lower screw) on each side, as

illustrated to the right. Use the Torx key.

The grille and Torx key are found in the foot module box. The

screws are premounted in the grille and bottom module.

Follow these steps to fasten the grille:

Remove the two upper screws from the grille.

Loosen the two lower screws in the bottom module

without removing them.

Place the front grille below the front door, as illustrated

to the right. Tilt the front grille to get the brackets behind

the front door and slide the grille on to the lower screws.

Open the front door to gain access to the screws.

Insert the upper screws without tightening them.

Close the front door to align the grille.

Open the front door again, and tighten the lower

screws through the hole.

Tighten the upper screws.

PRECAUTIONS

Please follow the steps in this installation guide when unpacking

and assembling Profile 42"/52". A minimum of two (2) persons are

required when installing Profile 42"/52".

UNPACKING THE SYSTEM AT THE DESTINATION

It is highly recommended to start the unpacking and assembling of

Profile 42"/52" at the place where the system is to be used.

NOTE:

If it is not possible to bring the complete delivery to the room

where Profile 42"/52" is to be used, then unpack (step 1–2) and

bring the smaller units to the destination.

• The monitor box requires two (2) persons to lift

(42" 110 lb / 50 kg, 52" 132 lb / 60 kg)

• The column requires two (2) persons to lift (55 lb / 25 kg)

• The stand-alone foot module requires two (2) persons to lift (55 lb /

25 kg)

Remove the outer cover and locate the boxes for the monitor, column, camera, touch screen and accessories

HEAVY

CAUTION

Monitor

(42" 110 lb / 50 kg,

52" 132 lb / 60 kg)

Column

(55 lb /25 kg)

HEAVY

CAUTION

Detailed illustration from inside, left

hand side. Right hand side is similar.

Upper screw

(M6×16)

Hole to access

the lower screw

Front grille

Lower screw

(M6×10)

Detailed illustration, left hand side.

Right hand side is similar.

Page 1

INSTALLATION NEAR A SOCKET-OUTLET

The equipment must be installed near a socket-outlet. The socket-

outlet shall be easily accessible after installation.

ROOM GUIDELINES

NOTE:

The floor must be in level.

The recommended distance between the Profile 42"/52" and

the meeting room table should be minimum 59 in. / 150 cm.

Read more about room guidelines in the Video conferencing room

primer.

USER DOCUMENTATION

The user documentation for this product, including compliance and

safety information, is available on the Cisco web site.

Go to: http://www.cisco.com/go/telepresence/docs.

The accessories box contains:

Rev. Date

Prep.

Checked Change

Telecom AS

Sheet 1 of 1

Specification:

Material

Processes

Tolerances

Type:

European

121608 rev.

Manufacturer:

projection

Type number:

Thickness:

Unit:

Dimensions without paint or finish

Color:

Sheet size:

All materials, finishes, and proccesses

Surface:

Glossiness:

Scale:

1:7

must comply with the RoHS directives

Flame class:

3D CAD model file 121608 rev. 01 is master

Part weight:

Flame class requirement: -

UL reference:

Mounting the wheelbase foot module

CAUTION:

You need two persons to mount the

column to the wheelbase. Take care to hold the

modules firmly during installation.

Unpack the column. Hold it firmly while moving

the wheelbase towards the bottom of the

column, aligning the holes for the screws.

Use the Allen key, which is

Front door

found in the foot module

box, to fasten the four

M8×30 screws.

Raise the complete

bottom module.

Telecom AS

Sheet 2 of 2

Processes

Tolerances

Speci cation:

Material

Surface treatment

Type:

European

117324 rev.00A+

Manufacturer:

projection

Type number:

TANDBERG Aquarius 52"

Thickness:

Unit:

Dimensions without paint or nish

Color:

Sheet size:

Surface:

All materials, nishes, and proccesses

must comply with the RoHS directives

Glossiness:

Scale:

1:5

Flame class:

3D CAD model le 117324

rev. 00E+ is master

Part weight:

53908g

Flame class requirement: -

UL reference:

Rev. Date

Prep.

Checked Change

Telecom AS

117324 rev.00A+

TANDBERG Aquarius 52"

DIMENSIONS OF PROFILE 42"

The assembled unit has the following dimensions:

• Height: 59.9 in. / 152 cm

• Width: 38.6 in. / 98 cm

• Depth: Stand-alone: 26.8 in. / 68 cm

Wall mounting: 8.9 in. / 23 cm (brackets included)

Wheelbase: 31.8 in. / 81 cm

• Weight: 231.5 lb / 105 kg

DIMENSIONS OF PROFILE 52"

The assembled unit has the following dimensions:

• Height: 63.6 in. / 162 cm

• Width: 47.4 in. / 121 cm

• Depth: Same as for Profile 42"

• Weight: 253.5 lb / 115 kg

Touch screen

Camera

Accessories box

• Microphones, 2 or 3 pcs.

• Cleaning cloth

Surface treatment

• Remote control and 4 AAA

• Power cables

batteries

• Two M8×60 screws

Sheet 1 of 2

Processes

Tolerances

Specification:

Material

Surface treatment

Type:

European

Manufacturer:

projection

Type number:

Thickness:

Unit:

Dimensions without paint or finish