Sony ZS-S2iP Instruções de utilização - Página 2
Procurar online ou descarregar pdf Instruções de utilização para Sistema estéreo Sony ZS-S2iP. Sony ZS-S2iP 2 páginas. Personal audio system
Também para Sony ZS-S2iP: Especificações (2 páginas), Instruções de utilização (2 páginas)
Imprimir página
Basic Operations
and
VOLUME +
have a tactile dot.
VOLUME +
have a tactile dot.
Opening/closing the Sliding Tray
Playing a CD
1
Press CD
Setting the iPod
2
Press PUSH OPEN/CLOSE
1
Press the PUSH OPEN/CLOSE button
.
with the label side up in the CD compartment.
The Sliding Tray
is ejected half way.
To close the CD compartment, press PUSH OPEN/
2
Pull the Sliding Tray
all the way out.
CLOSE
3
Attach the iPod Universal Dock Adapter if
necessary (not supplied).
4
Place your iPod on the Sliding Tray
.
3
Press
The player plays all the tracks once.
5
Push in and adjust the Sliding Tray
so that the
Track
iPod fits on the Back Support
.
number
To
Pause playback
Back
Stop playback
Support
Go to the next
track
Go back to the
Closing the Sliding Tray
previous track
1
Remove the iPod
Locate a point
while listening to
the sound
Locate a point
while observing
the display
Remove the CD
Using the display
2
Push the Sliding Tray
until it clicks.
3
Press the PUSH OPEN/CLOSE button
.
To check the total track number and playing
4
Push the Sliding Tray
into the unit.
time
Notes
In stop mode, press DISPLAY•ENTER
• Do not carry the unit with an iPod set on the connector. Doing so
on the remote.
may cause a malfunction.
• Be sure to store the Sliding Tray
before moving the unit.
To check the remaining time
Press DISPLAY•ENTER
remote repeatedly while playing a CD. The display
Playing the iPod
changes as follows:
The current track number and playing time
1
Press iPod
(direct power-on).
"DC OUT" appears in the display (AC only).
The current track number and the remaining
time of the current track*
The number of tracks left and remaining
time on the CD
2
Press
.
* For a track whose number is more than 20, the remaining time
The iPod begins to play.
appears as "- -:- -" in the display.
You can operate the connected iPod by the unit or the
iPod buttons.
To
Press
Pause playback
To resume play, press it again.
Stop playback
Go to the next
track
Go back to the
previous track
Locate a point
(forward) or
(backward)
while listening to
while playing and hold it until
the sound
you find the point.
Locate a point
(forward) or
(backward)
while observing
in pause and hold it until you
on the iPod
find the point.
display
Select a menu
Press MENU and
or
on the
remote to select a menu, and then
press ENTER
.
Go back to the
Press MENU
on the remote.
previous menu
Notes
• You may use the universal adaptor supplied with your iPod for a
more customized fit. The iPod may be docked without the use of an
adaptor.
• If you connect the iPod when another function is in use, the
function will change to iPod automatically.
• Apple's iPod Universal Dock Adapter (not supplied) can be used
with this unit.
• To use an iPod, refer to the user's guide of your iPod.
• Before disconnecting the iPod, pause playback.
To use the unit as a battery charger (AC
only)
You can use the unit as a battery charger. The charging
status appears in the iPod display. For details, see the
user's guide of your iPod.
On copyrights
• iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
• All other trademarks and registered trademarks are
of their respective holders. In this manual, ™ and ®
marks are not specified.
• Apple is not responsible for the operation of this device
or its compliance with safety and regulatory standards.
Selecting the play mode
Press MODE
until "
(direct power-on).
and " ", "PGM", or "PGM" and " " appear in
and place a disc
the display. Then proceed as follows:
To Select
Select
Repeat a
"
.
single track
Repeat all
" "
tracks
Shuffle play "SHUF"
Repeat tracks
"SHUF"
in random
and " "
order
Program
"PGM"
.
play
Playing
time
Press
Programed
track
To resume play, press it again.
Repeat
"PGM"
programed
and " "
tracks
(forward) or
(backward)
To cancel the selected play mode
while playing and hold it until
Press MODE
repeatedly until the selected mode
you find the point.
disappears from the display.
(forward) or
(backward)
in pause and hold it until you
To check the programed track and playing
find the point.
order in the display
PUSH OPEN/CLOSE
To check the order of tracks before play, press
DISPLAY•ENTER
Every time you press the button, the track number
appears in the programed order.
To change the current program
Press
once if the CD is stopped and twice if the
CD is playing. The current program will be erased.
Then create a new program following the programing
or DISPLAY
procedure.
Tip
You can play the same program again, since the program is saved
until you open the CD compartment.
or DISPLAY
on the
Listening to the radio
1
Press RADIO•BAND•AUTO PRESET
repeatedly (direct power-on) or press RADIO
and press BAND
Each time you press the button, the indication
changes as follows:
"FM" "AM"
2
Hold down TUNE + or –
digits begin to change in the display.
The player automatically scans the radio frequencies
and stops when it finds a clear station.
If you can't tune in a station, press the button
repeatedly to change the frequency step by step.
When an FM stereo broadcast is received, "ST"
appears.
Tips
• If the FM broadcast is noisy, press MODE
in the display and the radio will play in monaural.
• If you touch or operate an iPod connected to this unit while
listening to AM/FM, noise may occur. Avoid touching or operating
the iPod in this case.
• If you hear noise from the AM/FM while supplying power to
iPod ("DC OUT" indicator appears in the display), press and hold
MODE for a few seconds to stop the power supply to the iPod ("DC
OUT" indicator disappears from the display).
Presetting radio stations
1", " ", "SHUF", "SHUF"
You can store radio stations into the player's memory.
You can preset up to 30 radio stations, 20 for FM and 10
for AM in any order.
1
Press RADIO•BAND•AUTO PRESET
Then do this
BAND
on the remote to select the band.
1"
Press
or
to
2
select the track that you want
Hold down RADIO•BAND•AUTO PRESET
or RADIO
on the remote for 2 seconds until
to repeat, then press
.
"AUTO" flashes in the display.
Press
.
3
Press DISPLAY•ENTER
remote.
Press
.
The stations are stored in memory from the lower
Press
.
frequencies to the higher ones.
If a station cannot be preset automatically
Press
or
then
You need to preset a station with a weak signal
press DISPLAY•ENTER
manually.
or ENTER
on the remote
1
Press RADIO•BAND•AUTO PRESET
for the tracks (up to 20) you
BAND
on the remote to select the band.
want to program in the order
2
you want. Then press
.
Tune in a station you want.
3
Hold down DISPLAY•ENTER
on the remote for 2 seconds until the preset
Playing
number flashes in the display.
order
4
Press PRESET + or –
Press
or
then
you want for the station flashes in the display.
press DISPLAY•ENTER
5
Press DISPLAY•ENTER
or ENTER
on the remote
remote.
for the tracks (up to 20) you
The new station replaces the old one.
want to program in the order
you want. Then Press
.
Tip
The preset radio stations remain in memory even if you unplug the
AC power cord or remove the batteries.
Playing preset radio stations
1
Press RADIO•BAND•AUTO PRESET
BAND
on the remote to select the band.
or ENTER
on the remote.
2
Press PRESET + or –
station.
Connecting optional components
You can enjoy the sound from an optional component
such as a portable digital music player through the
speakers of this unit. Be sure to turn off the power of
each component before making any connections. For
details, refer to the instruction manual of the component
to be connected.
1
Connect the AUDIO IN jack
the line output jack of the portable digital music
player or other components using an audio
connecting cable (not supplied).
2
Turn the unit and the connected component on.
repeatedly on the remote.
3
Press AUDIO IN
and start playing sound on
the connected component.
The sound from the connected component is output
from the speakers.
until the frequency
To connect the unit to a TV or VCR, use an extension
cable (not supplied) with a stereo-mini jack on one
end and two phono plugs on the other end.
until "Mono" appears
or
or ENTER
on the
or
or ENTER
until the preset number
or ENTER
on the
or
to tune in the stored
on the unit to