Cisco ASR 9000 Series Manual de configuração - Página 46
Procurar online ou descarregar pdf Manual de configuração para Hardware de rede Cisco ASR 9000 Series. Cisco ASR 9000 Series 50 páginas. Line card
Também para Cisco ASR 9000 Series: Configuração das definições de rede (26 páginas), Manual de configuração (46 páginas), Manual (24 páginas), Configuração (46 páginas), Manual (44 páginas), Manual de referência rápida (7 páginas)
Imprimir página
Configuration Examples for Serial Interfaces
RP/0/0RP0RSP0/CPU0:router (config-subif)#ipv4 address 10.20.3.1/24
RP/0/0RP0RSP0/CPU0:router (config-subif)# pvc 16
RP/0/0RP0RSP0/CPU0:router (config-fr-vc)# encapsulation ietf
RP/0/0RP0RSP0/CPU0:router (config-fr-vc)# commit
RP/0/0RP0RSP0/CPU0:router(config-fr-vc)# exit
RP/0/0RP0RSP0/CPU0:router(config-subif)# exit
RP/0/0RP0RSP0/CPU0:router(config)# exit
RP/0/0RP0RSP0/CPU0:router# show interface serial 0/1/0/0
Wed Oct
Serial0/1/0/0 is up, line protocol is up
Interface state transitions: 5
Hardware is Serial network interface(s)
Internet address is 10.20.3.1/24
MTU 4474 bytes, BW 44210 Kbit
reliability 255/255, txload 0/255, rxload 0/255
Encapsulation FRAME-RELAY, crc 16,
Scrambling is disabled, Invert data is disabled
LMI enq sent
LMI enq recvd 880, LMI stat sent
LMI DLCI 1023
Last clearing of "show interface" counters 02:23:04
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
858 packets input, 11154 bytes, 0 total input drops
0 drops for unrecognized upper-level protocol
Received 0 runts, 0 giants, 0 throttles, 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
858 packets output, 12226 bytes, 0 total output drops
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
The following example shows how to create a serial interface on a SPA with Frame Relay encapsulation
and a serial subinterface with a PVC on router 2, which is connected to router 1:
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/1/0/1
RP/0/0RP0RSP0/CPU0:router(config-if)# encapsulation frame-relay
RP/0/0RP0RSP0/CPU0:router(config-if)# no shutdown
RP/0/0RP0RSP0/CPU0:router(config-if)# end
Uncommitted changes found, commit them? [yes]: yes
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/1/0/1.1 point-to-point
RP/0/0RP0RSP0/CPU0:router (config-subif)#ipv4 address 10.20.3.2/24
RP/0/0RP0RSP0/CPU0:router (config-subif)# pvc 16
RP/0/0RP0RSP0/CPU0:router (config-fr-vc)# encapsulation ietf
RP/0/0RP0RSP0/CPU0:router (config-fr-vc)# commit
Cisco ASR 9000 Aggregation Services Router Interfaces and Hardware Component Configuration Guide
544
8 04:14:39.946 PST DST
0, LMI stat recvd 0, LMI upd recvd 0
LMI type is CISCO
Configuring Serial Interfaces on the Cisco ASR 9000 Series Router
880, LMI upd sent
0 , DCE LMI up
frame relay DCE
OL-26061-03