Epson LQ 1070 - B/W Dot-matrix Printer Manual de informações do produto - Página 3
Procurar online ou descarregar pdf Manual de informações do produto para Acessórios para impressoras Epson LQ 1070 - B/W Dot-matrix Printer. Epson LQ 1070 - B/W Dot-matrix Printer 8 páginas. Hi-capacity cut-sheet feeder
Também para Epson LQ 1070 - B/W Dot-matrix Printer: Manual de montagem (8 páginas)
Imprimir página
The Control Panel
The indicator lights give you the current status of the printer. The
buttons let you control many of the printer settings.
Lights
OPERATE (green)
On when operate switch is on and power is supplied.
PAUSE (yellow)
On when the printer is not ready to print data. Stays off unless you
PAUSE
press the
button to prevent printing.
DATA (yellow)
On when data is present in the printer's buffer.
MULTI-PART (green)
On when you move the paper-thickness lever to position 2 or higher.
The printing speed is reduced when this light is on.
PAPER OUT
(red)
On when the printer runs out of paper.
On when bin 1 of the optional cut-sheet feeder is selected for paper
feeding.
BIN
2 (green)
On when bin 2 of the optionai cut-sheet feeder is selected for paper
feeding.
TEAR OFF (yellow)
TEAR OFF
On when you press the
off position
On when a specific font is selected.
Buttons
PAUSE
Press this button to temporarily stop printing. Press this button again
to resume printing.
LOAD/EJECT
Press this button to load single-sheet or continuous paper to the
loading position (however, the printer normally loads paper
automatically). If single-sheet paper is already in the loading
position, use this button to eject the sheet. lf continuous paper is in
the loading or tear-off position, press this button to feed it backward
to the standby position.
feed/Form feed)
Tap this button briefly to feed the paper forward one line. Hold this
button down to eject a single sheet of paper or advance continuous
paper to the top of the next page. You can also use this button to load
a single sheet of paper from the cut-sheet feeder or to feed
continuous paper from the standby position to the loading position.
24-Pin Printers
button to feed the paper to the tear-
ALT
results in the following:
BUFFER CLEAR
(PAUSE)
increments
Bin Sale&TEAR OFF
This button selects the paper bin when both optional cut-sheet
feeders are installed and you are printing on single sheets. When
printing on continuous paper, press this button once to feed paper
from
the loading position to the tear-off position. Press this button
again to feed the paper backward to the loading position.
CONDENSED
Press this button to print condensed characters. Press again to return
to normal character printing.
FONT
Press this button to select from among the built-in fonts.
Note: The panel's font name typestyles are meant as guides only;
actual minted results may differ slightly.
Other control-panel features
The control panel also gives you access to two special functions:
down the LF/FF
self test:
Hold
LOAD/EJECT
the
printer to perform the self test. The self test lets you
check that your printer is operating properly and gives
you a printout of the current DIP-switch settings.
Data dump: Hold down both the
button while turning on the printer to enter data dump
mode. Data dump mode allows advanced users to find
the cause of communication problems between the
printer and the computer.
Setting the DIP Switches
DIP-switch tables
The section below shows the settings and functions of each DIP
switch. You can see the current DIP-switch settings at any time by
running the self test.
Table I DIP switch I
SW
l - l
character tables'
1-2
l-3
1-6
1-7
Input buffer
1 -Inch &D-over-Derforatlon
l-6
8/20/91
LQ-570/1070
clears the printer's buffer and intitializes
feeds paper forward in l/ 180~inch
feed paper backward in 1 /lB@inch
button (for LQ printing) or the
button (for draft printing) while turning on
LOAD/EJECT
button and
ON
See Tables 3 and 4 below
I On
LQ-570/1070-3