Acuity Brands Lighting ATB2 Series Instruções de instalação

Procurar online ou descarregar pdf Instruções de instalação para Lanterna Acuity Brands Lighting ATB2 Series. Acuity Brands Lighting ATB2 Series 3 páginas.

Imprimir página

INSTALLATION INSTRUCTIONS

DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.

READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION

RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.

TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL

AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION, CONSULT LOCAL CODE AUTHORITY

TERMINAL

BLOCK COVER

TERMINAL

BLOCK

WARNING

ENSURE THAT ALL POWER IS

DISCONNECTED PRIOR TO WIRING

WIRING:

PULL UP TERMINAL BLOCK COVER (OPTIONAL) AS SHOWN IN

THE PICTURE. FEED THE SUPPLY WIRES THROUGH THE MAST

ARM, DRESS THEM SO THEY DO NOT INTERFERE WITH ANY

COMPONENTS AND SO THEY WILL NOT BE PINCHED IN THE

DOOR, AND CONNECT THEM TO THE PROPER TERMINALS ON

THE TERMINAL BLOCK. VERIFY THE SUPPLY VOLTAGE IS

CORRECT AS NOTED ON THE NAMEPLATE LABEL. IF SUPPLIED,

PUSH DOWN THE TERMINAL BLOCK COVER TO KEEP

TERMINALS COVERED.

WARNING

FIXTURE MUST BE GROUNDED

TO FUNCTION AS INTENDED

TERMINAL BLOCK:

RECOMMENDED TORQUE FOR SCREWS 35 IN-LBS.

DRAWING NO. A72975 REV: A (FRONT)

American Electric Lighting a division of Acuity Brands Lighting

ATB2 SERIES LUMINAIRES

FITTER BOLTS MAST ARM

KNOCKOUT

WARNING

CAUTION

OVER-TORQUING OF FITTER CLAMP BOLTS CAN

CREATE CRACKS IN THE HOUSING CAUSING

THE FIXTURE TO FALL TO THE GROUND.

MOUNTING / LEVELING

DETERMINE THE SIZE OF THE MAST ARM. THIS LUMINAIRE IS

DESIGNED TO ACCOMMODATE A MAST ARM FROM 1/1/4" TO 2"

DIA. THE LUMINAIRE IS FACTORY SET TO MOUNT TO THE 1-1/4"

ARM. TO MOUNT TO A 2" ARM, A MODIFICATION MUST BE MADE.

THE REAR OPENING MUST BE ENLARGED. KNOCKOUTS ARE

CAST-IN AROUND THE REAR OPENING FOR THIS PURPOSE. TO

REMOVE THIS EXCESS MATERIAL, STRIKE WITH A HAMMER OR

GRASP WITH PLIERS AND BREAK OFF.

STANDARD MOUNTING

LOOSEN (DO NOT REMOVE) THE FITTER BOLTS. LIFT THE

LUMINAIRE INTO POSITION IN FRONT OF THE MAST ARM SUCH

THAT THE MAST ARM ENTERS THROUGH THE OPENING AT THE

REAR OF THE LUMINAIRE AND BETWEEN THE FITTER BRACKET

AND THE LUMINAIRE HOUSING. TIGHTEN FITTER BOLTS

TO 10-12 FT-LBS.

ANGLE LEVELING:

THIS LUMINAIRE IS DESIGNED TO ADJUST ± 5 DEGREES UP OR

DOWN SIDE. TO ADJUST THE LUMINAIRE TO THE UP SIDE, TIGHTEN

THE REAR FITTER BOLTS UNTIL GET THE DESIRED ANGLE, AND

THEN TIGHTEN THE FRONT FITTER BOLTS TO SECURE THE

LUMINAIRE. TO ADJUST TO THE DOWN SIDE TIGHTEN THE FRONT

FITTER BOLTS UNTIL GET THE DESIRED ANGLE, THEN TIGHTEN THE

REAR FITTER BOLTS TO SECURE THE LUMINAIRE.

OPTIONAL PHOTOCONTROL:

PLUG THE PHOTOCONTROL INTO THE RECEPTACLE ENSURING

GASKET IS FIRMLY SEATED. TWIST CLOCKWISE UNTIL IT LOCKS

INTO POSITION.

IF PHOTOCONTROL RECEPTACLE ROTATION IS REQUIRED, LOOSEN

THE TWO PHILIPS HEAD RECEPTACLE SCREWS. ROTATE

RECEPTACLE, MAXIMUM OF 360° , THEN RE-TIGHTEN SCREWS

UNTIL SNUG, USING 20-25 IN-LBS OF TORQUE.

IF PHOTOCONTROL RECEPTACLE ROTATION IS REQUIRED

FOR THE P5 / P7 OPTION, LOOSEN THE TWO PHILIPS HEAD

RECEPTACLE SCREWS COMPLETELY. ROTATE RECEPTACLE 90°,

180°, OR 270°, THEN RE-TIGHTEN SCREWS UNTIL SNUG, USING

20-25 IN-LBS OF TORQUE.

CAUTION

PART NUMBER 057-70-72975