Argox AR-300 Manual de início rápido

Procurar online ou descarregar pdf Manual de início rápido para Leitor de código de barras Argox AR-300. Argox AR-300 2 páginas.

Imprimir página
To program each option, you must:
1. Scan the Program barcode on the parameter setting part.
Introduction
2. Enter the option mode by scanning the Option Bar Code
RS-232
(also on the Parameter setting part).
1)
Disconnect power to the terminal/computer.
3. To the right of the option barcode, the necessary
2)
Connect the appropriate interface cable to the scanner
alphanumeric inputs are listed. Scan these alphanumeric
3)
Connect the external power supply (DC adapter) to the
entries from the back fold out page. To confirm above
scanner
4)
Plug the serial connector into the serial port on the back
steps, you must scan the Finish barcode on the back fold
of your computer/terminal. Tighten the two screws to
out page.
secure the connector to the port.
4. Once you have finished programming. Scan the Exit
5)
Plug the power pack into power source.
barcode, listed on the lower right hand corner of each
6)
Once the scanner has been fully connected, turn the
terminal/computer power back on.
parameter setting part.
USB (Simulate with keyboard wedge)
5. In this Quick Start Guide, you will only need to scan the
1)
Connect the USB cable between scanner and PC
single barcodes which are specially made for this QSG
2)
Windows will automatically detect the USB device.
(Quick Start Guide).
Note: If any of the above operation is incorrect, turn off the
power immediately and check any improper
Interface Selection
connections. Go through all above steps again.
Note: If you need more programming parameters to setup
RS-232
your ArgoScan scanner, please go to
www.argox.com
and download the completed user's
manual.
USB HID
Programming the ArgoScan AR-3000
To program the AR-3000, you must scan a series of
programming barcode in the correct order. Fold out the back
USB COM
cover of this manual, you will see a table of alphanumeric
barcodes, which are used to program the various options
RS-232/USB HID
*
presented.
Auto detection
To program each option, you must:
Note:
＊
-Default
1. Scan the Program barcode on the parameter setting part.
2. Enter the option mode by scanning the Option Bar Code
0
(also on the Parameter setting part).
Scan Mode
Scan Mode
Good-read off
Momentary *
Alternate
Timeout off
Continue
Test only
2
Keyboard Layout
USA *
Belgium
1
Danish
France
Germany
Italian
Portuguese
Italian
4800 BPS
Portuguese
9600 BPS *
Spanish
19200 BPS
Swedish
38400 BPS
57600BPS
Switzerland
UK
115200BPS
Latin American
RS-232 Flow Control
RS-232 Flow Control
None *
None *
Japanese
3
RTS/CTS
RTS/CTS
RS-232 Baud Rate Setting
Xon/Xoff
Xon/Xoff
300 BPS
ACK/NAK
ACK/NAK
600 BPS
RS-232 Parity Setting
RS-232 Parity Setting
1200 BPS
None *
None *
2400 BPS
Odd
Odd
4800 BPS
Even
Even
9600 BPS *
RS-232 Data Bit Setting
8 bits *
7 bits
Stand Mode Enable
Stand Mode Enable
Stand mode
Stand Mode Enable
Stand mode
+
Stand mode
+
+
5
Suffix Characters Setting
(HID & USB )
Suffix Characters Setting
(HID & USB )
Enter *
Suffix Characters Setting
(HID & USB )
Enter *
Enter *
Tab
Tab
Tab
None
4
None
None
Enable Barcode
Enable Barcode
Industrial 2 of 5
Enable Barcode
Industrial 2 of 5
Industrial 2 of 5
Matrix 2 of 5 Eur
Matrix 2 of 5 Eur
Matrix 2 of 5 Eur
Standard 2 of 5
Standard 2 of 5
Standard 2 of 5
Codabar
Codabar
Codabar