ARGSeguridad ZDAS-300 Manual do utilizador - Página 7
Procurar online ou descarregar pdf Manual do utilizador para Sistema de segurança ARGSeguridad ZDAS-300. ARGSeguridad ZDAS-300 16 páginas. Luxury voiced lcd alarm system
Imprimir página
If after 15 seconds the user does not press the * key to confirm the alarm, the panel will
auto dial next phone number.
After the entry of the listening in status, the next operating steps are same as the remote
control In section 4.9 previous.
4.11 Detector Battery Low Voltage Display On the Panel And Introduction
When detector has been in the low voltage state, it will not run correctly. The Panel can
receive the detector low voltage signal and display on the LCD and sound a beep to indicate
user to replace detector's battery in time.
Low voltage display and introductions:
A: When the panel is in the DISARMED mode, if the detector such as PIR detects itself
being low voltage, the panel will sound a beep every seconds and display the signal
On the LCD continually.
LOG
Figure 23: Detector No 2 in zone 3 is low voltage
B: When the panel is in the Armed/PART Armed mode, if the detector such as PIR detects
itself being low voltage, the panel will sound a beep every seconds and display the signal
armed zone and detectors No on the LCD alternately.
C: Even if the panel LCD displays the detector low Voltage, the operation also can be
done normally on the panel and stop provisionally low voltage display.
How to cancel the low voltage display:
A: Press 'Delete' key and - - - appears on the LCD. Press registered Key Fob or enter your
PIN, LCD will display 'DEL Sensor' u se keypad to select zone(s) 1 to 8. Use Keypad to select
Detector(s) 1 to 9. Program the 4th field with 0. Press Key Fob Exit. (Refer to figure 25)
B: Press the key Fob
N.B.: When the battery has been replaced, the user must program the 4the field with 0
manually. And then the panel will display normally.
23
M
D
H
M
D
+12V JD
Auto
L7
L6
L5
L4
L3
L2
output
1 2 V i n p u t
Power
Phone
Phone line
ON
Figure 3: The back view of the panel
Everything you need to know about your Security System is displayed on the Panel
keypad. The zones armed or disarmed and the important messages regarding system status
appear on the LCD screen.
2. 2 The LCD Character details and description
2.2.1 The panel LCD screen whole information shows as follows:
DIS PART
ARMED
M
WatchDog
LOG
SETRMOT TYPECONFIG ALM
ON=Sounder as alarm
OFF=Silent as alarm
ARMED
Panel armed
DIS
ARMED
Panel disarmed
PARTARMED
Panel part armed
Watchdog
Avaible
Event log
LOG
M
Month
D
Day
H
Hour
M
Minute
D
Weekday
Figure 4: All the info. the LCD displays
Note:
GND: the negative electrode of the
power supply , siren , wired
detector and alarm output
L1.L2.L3.L4.L5.L6.L7 (wired detector):
L1 LAMP GND
lamp out: connect the relay for turn
on the lamp, this signal is
high-low contral
+12v: continued output for the wire
sensor or other accessaries
OFF
JD: output 12V for the wired siren or
other accessaries when alarm
D
H
M
D
PIN TESTTIMED GSM PHONE
Set program
SET
RMOT
Remot Zone
TYPE
type System
CONFIG
config Alarm
ALM
Wireless sensor battery low voltage
Pin code
PIN
Walk test
Timed auto arm or disarm
TEST
TIMED
GSM signal avaible
C.s. Phone or user owner phone
GSM
PHONE
4