Toshiba TDP-S35U Manual do Proprietário - Página 13

Procurar online ou descarregar pdf Manual do Proprietário para Projetor Toshiba TDP-S35U. Toshiba TDP-S35U 25 páginas. Mobile projector
Também para Toshiba TDP-S35U: Especificações (2 páginas), Especificações (2 páginas)

Imprimir página

Basic operations

Turn on the power.

Turn on the power by following the instructions in "Turning on the power"

Select the language and the lamp power (When using the

first time).

When the projector is used for the first time after purchase, menu for language and

lamp power selection and configuration is displayed in English. (If the screen is out of

focus, adjust it according to the step

q Use the

button to select the

desired language and press the

Message for setup confirmation is displayed in a

selected language.

Then, the menu for lamp power selection and

configuration is displayed. It is automatically set as

Standard. To change the setting, follow the step w.

w Using the

button, select Standard

or Low for the lamp power (menu item)

and press the

button.

The lamp power, if selected, will be toggled without

pressing the

button. The display automatically

disappears in a few seconds.

Notes

• When the projector is turned on the next time, the Language and Lamp power

menus do not appear upon startup. However, if "Reset all" is executed from the

Default setting menu

, the Language and Lamp power menus will be

p.32

displayed the next time when the power is turned on.

• The language can also be set via the Display setting menu

via the Default setting menu

p.32

• This owner's manual assumes that English has been selected.

Activate the connected device.

Turn on and start the connected device such as a computer.

Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected

equipment.

Notes

• When [Auto input search] is set to [On] in the default setting menu

of the equipment which is connected and turned on is projected.

• Moving pictures generated with the DVD software for computers may appear unnatural if

it is projected with this projector, but it is not a malfunction.

p.22

English

French

German

button.

Italian

Spanish

Portuguese

Russian

Swedish

Turkish

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

and Lamp power

p.31

p.32

, the image

Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot

adjuster.

q Lift up the front of the projector to

the desired angle, then press the

foot adjuster release button.

The foot adjuster extends. Release the

button to lock the position.

w Turn the foot adjuster to fine-tune

the angle.

e To adjust the horizontal angle, use

the tilt adjuster.

To stow the foot adjuster, hold up the projector while pressing the foot adjuster

release button, then slowly lower the projector.

Adjusting the screen size and focus

q Use the zooming lever to adjust the screen

size.

w Use the focusing lever to adjust the focus.

Adjusting the volume with the

The speaker volume can be adjusted when an audio signal is being input.

Notes

• Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.

• A lamp is consumable item. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The

lifetime of the lamp depends on conditions of use.)

• The DMD

is made using extremely advanced technology, but there may be black spots

(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please

note that these are not malfunctions.

• Although this projector supports a wide range of RGB signals

supported by this projector (SVGA) will be expanded or shrunk, which will affect image

quality slightly. To view high-quality images, it is recommended that the computer's

external output should be set to SVGA (800 × 600) resolution.

• With some models of computer having LCD displays or the like, displaying images

simultaneously on the projector and the monitor's display may prevent the images from

displaying properly. If this happens, turn off the computer's LCD display. For information

on how to turn off the LCD display, see the owner's manual of your computer.

• If a signal not supported by the projector is input, the "Unsupported signal" will appear.

• If no signal is being input from the connected device, the "No signal" will appear.

• If an unavailable operation button is pressed, the

buttons

, any resolutions not

p.45

icon will appear.