Toshiba XE30U - TLP XGA LCD Projector Manual do Proprietário - Página 5
Procurar online ou descarregar pdf Manual do Proprietário para Projetor Toshiba XE30U - TLP XGA LCD Projector. Toshiba XE30U - TLP XGA LCD Projector 28 páginas. Mobile projector
Também para Toshiba XE30U - TLP XGA LCD Projector: Especificações (2 páginas), Especificações pormenorizadas (2 páginas)
Imprimir página
IMPORTANT SAFETY INSTRUCTIONS (Continued)
21. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Only the replacement of the lamp
should be made by users.)
22. Safety Check
Upon completion of any service or
repairs to this product, ask the
service technician to perform
safety checks to verify that the
product is in proper operating
condition.
23. Do not leave thermal-
paper documents or easily
deformed items on top of
the unit or near the air
exhaust for long periods
of time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
24. Do not use the product in
a closed installation
location.
Do not place the product in a box
or in any other closed installation
location. Otherwise it may
overheat, which could result in a
risk of fire.
8
POWER SUPPLY INFORMATION
If your line voltage is 220 to 240V, use one of the following types of cable/plug.
Plug
configuration Plug type
Line voltage
EURO
220 – 240V
UK
220 – 240V
Use a 5A fuse which is approved by ASTA
or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on
the lens and the crucial internal parts. Do not use the unit for at least 2 hours when there
is an extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,
shortening their lives, and darkening the screen.
• Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
• Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
• Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts. If you continue to use it in that situation,
it may malfunction. Wait until the condensation naturally disappears.
• In a high altitude location where air is thin, cooling efficiency is reduced so use the
projector with [Fan mode] set to [High].
• Only plug the power cord into outlets rated for use with the power cord's specified voltage
range. Do not overload extension cords or power strips as this can result in fire or electric
shock.
• Route the power cable or the connecting cable away from where people could trip over it.
The projector may fall, which could result in severe injury.
• Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Plug
configuration
Plug type
Line voltage
Australian
200 – 240V
240V
10A
Switzerland
200 – 240V
240V
6A
North American
200 – 240V
240V
15A
p.41
9