Dimplex 3078 Instruções de instalação e de utilização - Página 2

Procurar online ou descarregar pdf Instruções de instalação e de utilização para Aquecedor Dimplex 3078. Dimplex 3078 5 páginas. Convector heaters

Imprimir página

Dimplex Convector Heaters

Models : 3071, 3072, 3073, 3077 and 3078

Dimensions

(millimetres)

Models

Specification

3071

2.0kw Thermostat

3072

2.0kw Thermostat/24hr Timer/Neon

3073

2.0kw Switch/Thermostat

3077

2.0kw 2 Neon Switches/Thermostat/Turbo

3078

3.0kw 2 Switches/Thermostat/Neon

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.

IMPORTANT S FETY ADVICE

WARNING –THIS APPLIANCE MUST NOT BE USED IN A BATHROOM

WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE

SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL.

WARNING – THIS HEATER MUST NOT BE LOCATED IMMEDIATELY

BELOW A FIXED SOCKET OUTLET.

DO NOT USE THE HEATER UNTIL THE FEET OR WALL BRACKETS

ARE FITTED CORRECTLY.

FOLLOW these instructions carefully.

NEVER cover or obstruct in any way the heat outlet slots at the top

of the heater or the air inlet slots in the base of the heater.

The heater carries a warning 'DO NOT COVER' to alert the user to the

risk of fire that exists if the heater is accidentally covered.

If young children, the aged or infirm are likely to be left in the vicinity

of the heater, we advise that adequate precautions should be taken.-

We recommend that a guard be fitted to ensure contact with the

heater is avoided and objects cannot be inserted into the product.

Model 3072 – this model can be set to switch on automatically ,

remember to observe all safety warnings at all times .

If the mains lead is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified person in

order to avoid a hazard.

For further information, please contact our guard supplier direct on

Tel. No. 01603 667957, or in case of difficulty or for further advice

contact the Customer Helpline.

WARNING: In order to avoid a hazard due to inadvertent resetting of

the

thermal cut-out, this appliance must not be supplied t

external

switching device, such as a timer, or connected t

that is regularly switched on and off by the utility.

Electrical connection

RNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an ~ supply only and the voltage ma

the heater must correspond to the supply voltage. This heater

a re

wirable plug incorporating a 13 amp fuse. In the event of

fuse in the plug supplied, a 13 amp fuse approved by ASTA to B

must be used. If any other type of plug is used, a 15 amp fuse must be

fitted in the plug, the adaptor, or at the distribution board.

IMPORTANT : If the plug is not suitable for your socket, the 13

should be removed. Before wiring the appropriate plug, please n

the

wires in this mains lead are coloured in accordance with the f

code :

EEN AND YELLOW :

BLUE :

BROWN :

replacing the

EARTH

NEUTRAL

LIVE

Installation and Operating Instructions

230

697 - 3.0kw

MIN

577 - 2.0kw

432

Connect the GREEN AND YELLOW wire to the terminal marked 'E' or by

the earth symbol

Connect the BROWN wire to the terminal marked 'L' or coloured RED.

Connect the BLUE wire to the terminal marked 'N' or coloured BLACK.

Wall Mounting

Three identical wall mounting brackets are secured to the base of the

heater with a fixing screw. To wall mount appliance, first remove the

brackets as follows :

Lay the heater on its back. Following the sequence in Fig. 1 – identify

and remove the fixing screw securing the brackets located beside Mains

Cable as shown in (a), then pull out brackets and rotate them to

disengage them from the slot (b).

Withdraw the brackets from the slot (c).

(a)

Select a suitable position on a wall, near to a mains power socket,

making sure that there is at least 230 mm below the heater and at least

450 mm above the heater of unobstructed space. See also 'Positioning

the heater'.

Fix the two top retaining brackets to the wall, using suitable fixings, for

2kw models at 358 mm centres and 3kw models at 478 mm centres –

hrough an

see Fig 2.

o a circuit

rked on

is fitted with

S 1362

amp plug

ote that

ollowing

Locate the heater on the top brackets and allow it to hang in place.

Fit the bottom bracket into the slot in the heater and then fix it to the wall.

Test that the heater is now securely fixed to the wall.

INDCUK307R

230

156

MIN

Floor Mtd.

, or coloured GREEN or GREEN AND YELLOW.

(b)

(c)

3 No. Wall

Mounting

Brackets

Issue 4

450

MIN

357

230

MIN

Wall Mtd.

Fig. 1

shelf /

ceiling

526 mm

min.

bracket

slot

520 mm

min.

floor

Fig. 2