Dimplex AS12 Series Instruções de instalação - Página 3
Procurar online ou descarregar pdf Instruções de instalação para Aquecedor Dimplex AS12 Series. Dimplex AS12 Series 3 páginas. Architectural heaters
Também para Dimplex AS12 Series: Instruções de instalação (3 páginas)
Imprimir página
3. Wrap the supply ground wire around the green painted
ground screw & tighten.
!
NOTE: When heaters are mounted end to end, remove
the finished end plate, install a chase nipple and locknut in
the terminal box to ensure grounding continuity and to pro-
tect the wiring. Where headers are spaced apart, remove
the finishing end plate, and use rigid conduit (provided by
customer) for through wiring and ground continuity. Do not
exceed the allowable number of conductors allowed by the
National Electric Code.
4. Do a final and complete check of all wiring then replace the
terminal box covers being careful not to pinch any wires.
5. The front panel may now be installed.
Terminal Box Volumes in Cubic Inches
Left Hand Box 4"
Heater Style
AF12, AS12
W ARNING: TO PREVENT THE RISK OF FIRE, DO NOT
OPERATE THE HEATER WITHOUT THE FRONT PAN-
ELS IN PLACE.
•
Place the front panel over the flange of the bottom panel.
•
Hook the top back edge of the front panel over the top
panel, and secure with screws.
Operation
1. This heater must be properly installed before it is used.
2. Prior to energization remove all construction dirt (plaster,
sawdust, etc.) from interior and exterior of heater.
Dimplex baseboard heaters are designed and tested for safe
and trouble-free operation. All Dimplex baseboard heaters
are protected against overheating by a built-in thermal cutout.
Free airflow throughout the heater is extremely important for
the most efficient operation of the heater. Restricted airflow
may cause the thermal overload protector to cycle the heater
"ON and OFF". A cycling heater will not supply sufficient heat
to the room.
Avoid direct contact of paper, fabric, or furniture with heater.
1367 Industrial Road
Cambridge ON Canada N1R 7G8
1-888-346-7539
www.dimplex.com
In keeping with our policy of continuous product improvement, we reserve the right to make changes without notice.
© 2015 Dimplex North America Limited
Right Hand Box 5"
Wide
Wide
146.25
182.75
Maintenance
CAUTION: Before removing the front cover for cleaning,
make certain the power has been turned off at the circuit
breaker panel.
CAUTION: Allow adequate time for the element and body
casing to cool before attempting to work on the heater.
The AF12/AS12 series contain no moving parts. Since the
appliance contains no moving parts, little maintenance is
required beyond vacuum cleaning. It is, however, essential
that the heater is not operated with an accumulation of dust
or dirt on the element, as this can cause a build up of heat
and eventual damage. For this reason the heater must be
inspected regularly, depending upon conditions and at least at
yearly intervals. Once cleaning is complete replace the front
cover and restore power.
WARNING: The user can perform cleaning ONLY, all
other servicing should be performed by qualified service
personnel.
Warranty
The Manufacturer warrants the heating elements and components of
the enclosed product against any defect in material or workmanship
for a period of one year from the date of purchase, with the exception
of the elements which are warranted to be free from defect in mate-
rial and workmanship for ten years. In full satisfaction of any claims
under this Warranty the Manufacturer will repair or replace without
charge, in its factory or in the field as it alone may decide, any parts
which in its opinion are defective.
The Manufacturer shall not be responsible for any transportation or
shipping costs in relation to such repair or replacement except as
specifically assumed by it. Misuse of this product or repairs by per-
sons other than the Manufacturer's authorized personnel without the
Manufacturer's written approval, will void this Warranty.
This Warranty is in lieu of all other warranties or conditions whether
expressed or implied including but not limited to those of merchan-
tability or fitness for purpose and shall constitute the sole remedy of
the Purchaser and the sole liability of the Manufacturer in respect of
the sale of the product, whether in the nature of breach or breach of
fundamental term, or of negligence or otherwise.
The Manufacturer shall not be liable for any special, indirect or
consequential damages or for any damages resulting from remo-
val or replacement of a heater subject to warranty claim without the
Manufacturer's authorization. This Warranty is transferable by the
original consumer purchaser of the product. Any claims under this
Warranty must be submitted in writing to the Service Manager, Dim-
plex North America Ltd., 1367 Industrial Rd., Cambridge, Ontario
N1R 7G8, Canada.