Cru Power HT-S-2500 Manual - Página 2

Procurar online ou descarregar pdf Manual para Inversor Cru Power HT-S-2500. Cru Power HT-S-2500 3 páginas. Dc to ac

Imprimir página

Remote control-LCD

Power saving

function

Waveform

Battery capacity

High battery

Low battery

volt protection.

position, the inverter should supply

power to the load.

Installation

1. Where to install

The power inverter should be installed in a

location that meets the following requirements:

a. Dry - Do not allow water to drip or splash

on the inverter.

b. Cool - Ambient air temperature should

be between -15°C and +45°C, the cooler

the better.

c. Ventilated - Allow at least one inch of

clearance around the inverter for airflow.

Ensure the ventilation openings on the

rear and bottom of the unit are not

obstructed.

d. Safe - Do not install the inverter in the

same compartment as batteries or in any

compartment capable of storing flammable

liquids such as gasoline.

2. Cables

DC to AC inverters require high amperage/low

voltage DC power to low amperage/high

voltage AC power. To operate properly

connect inverter DC input terminals direct

to battery with heaviest wire available see

chart below:

Max Watts Out

Approx. Amps

150W

15A

300W

30A

600W

60A

1000W

100A

1200W

120A

1500W

150A

1800W

180A

2500W

250A

3000W

300A

3. Grounding

The power inverter has a lug on the rear

panel chassis ground. This is to connect

the chassis of the power inverter to the

ground. The ground terminals in the AC

outlets on the front panel of the inverter

are also connected to the ground lug.The

chassis ground lug must be connected

to a grounding point, which will vary

depending on where the power inverter is

installed. In a vehicle, connect the chassis

Battery volt

Load watts

Over temperature

ground to the chassis of the vehicle.

In a boat, connect to the boat's grounding

systems. In a fixed location, connect the

chassis ground lug to earth.

Warning!

Do not operate the power inverter

without connecting it to ground.

Electrical shock hazard may result.

Operation

To operate the power inverter, turn it on

using the ON/OFF switch on the front

panel. The power inverter is now ready to

deliver AC power to your loads. If you are

operating several loads from the power

inverter, turn them on separately after the

inverter has been turned on. This will

ensure that the power inverter does not

have to deliver the starting currents for all

the loads at once.

Controls and indicators

The ON/OFF switch turns the control

circuit in the power inverter on and off. It

does not disconnect power from the power

Req'd Wire Guage

inverter.

#16

Operating limits

#12

#6 or 2×#10

1.Overload / Auto re-start

The inverter would operate most AC loads

within its power rating. If the load is over

6 X #4

the specification, HT-S-2500 will auto re-

2 X #4

start first, if not success, the inverter

2 X #4

will shut down automatically.

2.Overtemp

The buzz will be noisy if the temperature is

too high, then the inverter will be shut down

automatically. Please re-set it after the

inverter got cooling.

3.Input voltage

The power inverter will operate from input

voltage range 10V-16V (12V spec.) or 20V-32V(2

4V spec.) or 40V-61V (48V spec.).

fault LED Indicator

ON/OFF switch

Overload

If the voltage drops too low(※1) or raise too

high(※2), the inverter will shut down automatically.

Before shut down, buzz noise will warn you.

※1:<10.0V (12V spec.) or <20V (24V spec.)

or <40V (48V spec.)

※2:>16V (12V spec.) or >32V (24V spec)

or >61V (48V spec.)

Maintenance

You should clean the exterior of the unit

periodically with a dry cloth to prevent

accumulation of dust and dirt.

At the same time, tighten the screws on

the DC input terminals.

Troubleshooting

Television interference :

Operation of the power inverter can interfere

with television reception on some channels.

If this situation occurs, the following steps

may help to alleviate the problem.

-Make sure that the chassis ground lug

on the back of the power inverter is solidly

connected to the ground system of your

vehicle, boat or home.

-Do not operate high power loads with

the power inverter while watching

television.

-Make sure that the antenna feeding

your television provides an adequate

(snow free) signal and that you are using

good quality cable between the antenna

and the television.

-Move the television as far away from

the power inverter as possible.

-Keep the cables between the battery

and the power inverter as short as possible

and twist them together with about 2 to 3

twists per foot. This minimizes radiated

interference from the cables.