Pioneer DEH 1900MP - Radio / CD Manual de instalação - Página 2
Procurar online ou descarregar pdf Manual de instalação para Recetor para automóvel Pioneer DEH 1900MP - Radio / CD. Pioneer DEH 1900MP - Radio / CD 4 páginas. Pioneer deh-1900mp: user guide
Imprimir página
Connecting the Units
This Product
Rear output
Fuse (10 A)
Antenna jack
Blue/white
Connect to system control terminal of
the power amp or auto-antenna relay control
terminal (max. 300 mA 12 V DC).
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free
With a 2 speaker system, do not connect
metal location.
anything to the speaker leads that are not
connected to speakers.
Perform these connections when using
the optional amplifier.
Connect with RCA cables
(sold separately)
System remote control
White
Gray
+
+
Front speaker
Front speaker
≠
≠
White/black
Gray/black
Left
Right
Green
Violet
+
+
Rear speaker
Rear speaker
≠
≠
Green/black
Violet/black
+
+
Rear speaker
Rear speaker
≠
≠
ENGLISH
Installation
Note:
•
Check all connections and systems before final
installation.
•
Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
•
Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
•
Do not install this unit where:
Power amp
— it may interfere with operation of the vehicle.
(sold separately)
— it may cause injury to a passenger as a result
of a sudden stop.
•
The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
•
Optimum performance is obtained when the unit
is installed at an angle of less than 60°.
60°
DIN Front/Rear-mount
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following installation
methods.
DIN Front-mount
DIN Rear-mount
1. Extend top and bottom of the trim ring outwards
Installation with the rubber bush
to remove the trim ring. (When reattaching the
trim ring, point the side with a groove downwards
Mounting sleeve
Dashboard
and attach it.)
•
It becomes easy to remove the trim ring if the
182
front panel is released.
53
Rubber bush
Screw
1. Insert the mounting sleeve into the dashboard.
•
When installing in a shallow space, use a sup-
2. Determine the appropriate position where the
plied mounting sleeve. If there is enough
holes on the bracket and the side of the unit
space behind the unit, use factory supplied
match.
mounting sleeve.
2. Secure the mounting sleeve by using a screwdriv-
er to bend the metal tabs (90°) into place.
3. Install the unit as illustrated.
Removing the Unit
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. (When reattaching the
trim ring, point the side with a groove downwards
3. Tighten two screws on each side.
and attach it.)
Use either truss screws (5 mm × 8 mm) or
•
flush surface screws (5 mm × 9 mm), depend-
•
It becomes easy to remove the trim ring if the
front panel is released.
ing on the shape of screw holes in the
bracket.
Trim ring
2. Insert the supplied extraction keys into both sides
of the unit until they click into place.
3. Pull the unit out of the dashboard.
Factory radio mounting bracket
ENGLISH
Fastening the front panel
If you do not plan to detach the front panel, the
front panel can be fastened with supplied screw.
Trim ring
Screw
Screw
Dashboard or Console