Pioneer DEH-1410UB Manual do Proprietário - Página 10

Procurar online ou descarregar pdf Manual do Proprietário para Recetor para automóvel Pioneer DEH-1410UB. Pioneer DEH-1410UB 18 páginas. Cd rds receiver

Imprimir página

Pioneer DEH-1410UB Manual do Proprietário

Installation

3 Antenna input

4 Fuse (10 A)

5 Wired remote input

Hard-wired remote control adaptor can be

connected (sold separately).

Power cord

1 To power cord input

2 Depending on the kind of vehicle, the func-

tion of 3 and 5 may be different. In this

case, be sure to connect 4 to 5 and 6 to

3 Yellow

Back-up (or accessory)

4 Yellow

Connect to the constant 12 V supply termi-

nal.

5 Red

Accessory (or back-up)

6 Red

Connect to terminal controlled by ignition

switch (12 V DC).

7 Connect leads of the same color to each

other.

8 Black (chassis ground)

9 Blue/white

The pin position of the ISO connector will dif-

fer depending on the type of vehicle. Connect

9 and b when Pin 5 is an antenna control

type. In another type of vehicle, never con-

nect 9 and b.

a Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

b Blue/white

Connect to auto-antenna relay control termi-

nal (max. 300 mA 12 V DC).

c Yellow/black

Only for DEH-1420UB, DEH-1400UB and

DEH-1400UBB.

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

d Speaker leads

White: Front left +

White/black: Front left *

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Green/black: Rear left * or subwoofer *

Violet: Rear right + or subwoofer +

Violet/black: Rear right * or subwoofer *

e ISO connector

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to con-

nect to both connectors.

Notes

! Change the initial setting of this unit. Refer

to REAR-SP (rear output setting) on page 7.

Refer to PREOUT (preout setting) on page 7.

The subwoofer output of this unit is monau-

ral.

Autogood products «130»

Installation

! When using a subwoofer of 70 W (2 Ω), be

sure to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and green/

black leads.

Power amp (sold separately)

Perform these connections when using the op-

tional amplifier.





1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately)

3 Connect with RCA cables (sold separately)

4 To Rear output or subwoofer output

5 Rear speaker or subwoofer

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the

vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1 Dashboard

2 Mounting sleeve

Section