Pioneer DEH-4500BT Manual de operação - Página 17

Procurar online ou descarregar pdf Manual de operação para Recetor para automóvel Pioneer DEH-4500BT. Pioneer DEH-4500BT 33 páginas. Cd rds receiver
Também para Pioneer DEH-4500BT: Manual de início rápido (8 páginas)

Imprimir página

Operating this unit

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the equalizer.

POWERFUL—NATURAL—VOCAL—CUSTOM1

—CUSTOM2—FLAT—SUPER BASS

The equalizer band and equalizer level can be cus-

tomized when CUSTOM1 or CUSTOM2 is se-

lected.

If selecting CUSTOM1 or CUSTOM2, complete

the procedures outlined below. If selecting other

options, press M.C. to return to the previous dis-

play.

! CUSTOM1 can be set separately for each

source. However, USB and iPod are all set to

the same setting automatically.

! CUSTOM2 is a shared setting used in com-

mon for all sources.

3 Press M.C. to display the setting mode.

4 Press M.C. to cycle between the following:

Equalizer band—Equalizer level

5 Turn M.C. to select the desired setting.

Equalizer band: 80HZ—250HZ—800HZ—2.5KHZ

—8KHZ

Equalizer level: +6 to –6

LOUDNESS (loudness)

Loudness compensates for deficiencies in the low-fre-

quency and high-frequency ranges at low volume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW (low)—MID (mid)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output which

can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)—OFF

(subwoofer off)

SUB.W CTRL (subwoofer adjustment)

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the following:

Cut-off frequency—Output level—Slope level

Rates that can be adjusted will flash.

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—100HZ

—125HZ—160HZ—200HZ

Output level: –24 to +6

Slope level: –6— –12

BASS BOOST (bass boost)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select a desired level.

0 to +6 is displayed as the level is increased or de-

creased.

HPF SETTING (high pass filter adjustment)

When you do not want low sounds from the subwoo-

fer output frequency range to play from the front or

rear speakers, turn on the HPF (high pass filter). Only

frequencies higher than those in the selected range

are output from the front or rear speakers.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the following:

Cut-off frequency—Slope level

3 Turn M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ—

100HZ—125HZ—160HZ—200HZ

Slope level: –6— –12

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the vo-

lume level of each source to prevent radical changes

in volume when switching between sources.

! Settings are based on the FM volume level, which

remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to SLA.

! USB and iPod are all set to the same setting auto-

matically.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

System menu

Important

PW SAVE (power saving) is canceled if the vehi-

cle battery is disconnected and will need to be

turned back on once the battery is reconnected.

When PW SAVE (power saving) is off, depending

on connection methods, the unit may continue to

draw power from the battery if your vehicle's igni-

tion doesn't have an ACC (accessory) position.

Press M.C. to display the main menu.

Section