Pioneer VSX-D601 Manual de Instruções - Página 17
Procurar online ou descarregar pdf Manual de Instruções para Recetor Pioneer VSX-D601. Pioneer VSX-D601 41 páginas. Audio/video stereo receiver
Imprimir página@) SCAN button
Operate
when
the INPUT
SELECTOR
is set to TUNER.
Station
frequencies assigned to the STATION CALL buttons are tuned in, one
after another, beginning with the current station no., for approximately
5 seconds each, The display section SCAN indicator will light. Press
the button again and the tuner remains tuned in to the station playing
when the button was pressed the second time.
Station frequencies not assigned to station numbers in the memory are
skipped.
When you have selected a CUSTOM MEMORY genre, memory scan
is performed on the stations in that genre.
(8) FM Mode AUTO/MONO button
Use to select the auto stereo mode or monaural mode when listening
to FM broadcasts. The monaural mode has been selected when the
FM MONO
indicator in the dispiay section is lit.
Auto stereo mode:
Normally, leave in this mode for reception. When a stereo FM broadcast
is received, {it will be automatically reproduced in stereo.
Monaural mode:
When receiving distant stations or stations with weak broadcast signals,
the input signal may be weak, thus resulting in increased noise during
FM stereo broadcasts. In this event, setting the receiver to the monaural
mode will reduce the noise. In this case, however, FM stereo broadcasts
will be reproduced in monaural sound.
NOTE:
This button has no effect en reception of AM broadcasts.
@) Tuning buttons
Use to selact the tuning moda. To select the AUTO tuning mode, press
this button to light the AUTO TUNING indicator in the display section.
To select the MANUAL tuning mode, switch off the AUTO TUNING
indicator.
AUTO tuning
When the — or + TUNING button is pressed, the receiver automatically
scans the broadcast station frequencies. When a broadcast is detected,
the scanning stops at that frequency.
NOTE:
Pressing the TUNING button (- or +} while scanning is taking place
causes scanning to stop.
MANUAL tuning
This lets you manually tune to particular broadcast frequencies. Each
press of the + or -» button raises or lowers the frequency by one tuning
step. For continuous scanning, keep the button pressed, then release
it to stop scanning.
DIRECT ACCESS tuning button: (Page 20)
When this button is pressed, the STATION CALL buttons function as
ten-key number
buttons
for direct input of the desired
reception
frequency. Press again to cancel this mode.
\f the input station falls outside of the receiver's tuning range, the display
section will display a message: "UPPER" if the frequency is too high
and 'LOWER' if it is too low.
HITS (Hyper Intelligent Tuning System) button: (Page 22)
Press this button, and search automatically begins up and down the
frequency for stations that can be received. When a station that can
be received is found, the search operation stops.
FRONT PANEL FACILITIES
STATION CALL buttons
Up to 30 FM or AM stations can be preset at random.
These
buttons are used to preset and recall desired broadcasting
stations, FM AUTO/MONO
mode.
NOTE:
Pressing a STATION CALL button will select TUNER as the source,
regardless of what other listening source or function was selected.
They are also used when performing direct access tuning,
@) SIMULATED STEREO button
Press to produce a simulated stereo effect when listening to monaural
sources (for example, normal AM or TY broadcasts),
"SIMULATED
STEREQ" appears on the display section
NOTE:
° This effect is not produced through the rear speakers.
° Use with the SURROUND MODE in the OFF.
@ SURROUND MODE selector buttons
See page 5 'SURROUND EFFECT",
@ BALANCE buttons
Use them to adjust the sound volume balance between left and right
speakers.
L: Press to decrease the sound on the right side.
R: Press to decrease the sound on the left side.
Press L and R together te bring the volume balance back to center.
NOTE:
The left-right sound volume balance cannot be adjusted on the rear
speakers.
(@@ TREBLE control buttons
Use to adjust the high-frequency level. Press the + button to increase
the high-frequency level, and the
- - button to decrease it.
The TONE indicator appears on the display section,
When
both buttons
(-,
+} of the TREBLE
contro! are pressed
simultaneously, the treble response will be set to the flat (normal)
condition.
@® BASS control buttons
Use to adjust the low-frequency tevel. Press the + button to increase
the low-frequency level, and the
-- button to decrease it.
The TONE indicator appears on the display section,
When
both
buttons
(-,
+) of the
BASS
control
are
pressed
simultaneously, the bass response
will be set to the flat (normal)
condition.
@ DSP EFFECT/DELAY TIME buttons
[DSP EFFECT]
When
using a surround
mode
other than
DOLBY
PRO
LOGIC
SURROUND, 10-step adjustment of the effect level is possible from
10 to 100.
[DELAY TIME]
Operates when the DOLBY PRO LOGIC SURROUND mode is ON.
Switches to surround delay time in 8 steps. For DOLBY PRO LOGIC
SURROUND, 20 ms is standard.
Changes in 2 ms steps.
16 ms
«+ 18 ms ++--- «+28 ms «+30 ms
7
<ARBIZEO>
En