Pioneer VSX-LX302 Manual básico - Página 26
Procurar online ou descarregar pdf Manual básico para Recetor Pioneer VSX-LX302. Pioneer VSX-LX302 36 páginas.
Imprimir página
> Before Start
> Part Names
∫ 1. Full Auto MCACC
Place the supplied speaker setup microphone in the listening
position, measure the test tones emitted by the speakers, then
the unit automatically sets the optimum volume level for each
speaker, the crossover frequencies, and the distance from the
listening position. It also adjusts the volume of the separate
frequency ranges for each speaker so that the frequency
balance over the entire system is adjusted.
0 Calibration takes between 3 and 12 minutes to be completed.
The speakers emit the test tone at high volume during
measurement, so be careful of your surroundings. Keep the
room as quiet as possible during measurement.
0 If you have connected a subwoofer, check the power and volume of
the subwoofer. Set the subwoofer volume to more than halfway.
0 If the power of this unit suddenly turns off, the speaker
cables may have touch the rear panel or other wires and
tripped the protection circuit. Twist the wires again
properly and make sure they do not stick out of the
speaker terminals when connecting.
1. Place the supplied speaker setup microphone in the
listening position, and connect to the MCACC SETUP
MIC jack on the main unit.
MCACC
SETUP MIC
When putting the speaker setup microphone on a tripod,
refer to the illustration when putting it in place.
2. Select the connected speaker configuration.
26
> Install
> Initial Setup
The image on the screen changes as you choose the
number of channels in "Speaker Channels", so refer to it
when performing the settings.
3. Test tones are emitted by the speakers, and firstly the
unit detects the speakers connected and the noise in the
environment.
4. After the results of the above measurements are
displayed, select "Next", press ENTER on the remote
controller, and the test tones are emitted again, and the
unit automatically makes settings such as the optimum
volume level and the crossover frequency.
5. When the measurement is completed, the measurement
result is displayed. Press the cursors /
remote controller to check the settings. Press ENTER
when "Save" is selected to save the settings.
6. Disconnect the speaker setup microphone.
∫ 2. Source Connection
Check that each input source is connected correctly. Follow
the guidance, select the input you want to confirm, start
play of the selected player, and confirm that the images
appear on the TV and that sound is played.
∫ 3. Network Connection
Set up Wi-Fi connection with an access point such as a
wireless LAN router. There are the following two methods of
connecting by Wi-Fi:
"Scan Networks": Search for an access point from this
unit. Find out the SSID of the access point beforehand.
> Playback
"Use iOS Device (iOS7 or later)": Share the iOS device's
Wi-Fi settings with this unit.
If you select "Scan Networks", there are a further two
choices of connection method. Check the following.
"Enter Password": Enter the password (or key) of the
access point to connect.
"Push Button": If the access point has an automatic
connection button, you can connect without entering a
password.
0 If the SSID of the access point is not displayed, then in
the screen listing the SSIDs, select "Other..." with the
cursor on the remote controller and press ENTER, then
follow the onscreen instructions.
Keyboard Input
To switch between upper and lower case, select "A/a" on
the screen and press ENTER. To select whether to mask
the password with "¢" or display it in plain text, press +Fav
on the remote controller. Press CLEAR to delete all the
input characters.
on the
∫ 4. Multi Zone Setup
Make these settings to enjoy video and audio in a room
other than the main room (ZONE 2).
Select "Using AV Receiver" when connecting speakers in
the separate room. Select "with External Premain Amplifier"
when connecting a pre-main amplifier in the separate room.
Select "with External Power Amplifier" when connecting a
power amplifier.
If you are going to be connecting a TV in the separate room
(ZONE 2), then when "Would you be using TV in 2nd
room?" is displayed, select "Yes".
∫ 5. Audio Return Channel
If you have connected a TV that supports ARC, select "Yes". This unit's
ARC setting turns on and you can listen to the TV's audio through this unit.
0 If you select "Yes", the HDMI CEC function is enabled
and power consumption increases during standby.