Pioneer VSX-9700S Manual de Instruções - Página 45

Procurar online ou descarregar pdf Manual de Instruções para Recetor estéreo Pioneer VSX-9700S. Pioneer VSX-9700S 48 páginas.

Imprimir página
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunction. If you think that there is something wrong with this component, check the points
below. Sometimes the trouble may lie in another component. investigate the other components and electrical appliances being used.
lf the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer
to carry out repair work.
Power does not come on even
© Power cord is disconnected.
© Connect cord securely.
when POWER switch is pressed. | ¢ Instances are rare, but the problem may be due
e Unplug the power cord of the unit from the AC
to the operation of the protector circuit.
wall outlet, then plug it in again.
© Unplug the power cord of the unit from the AC
wall outlet, then plug it in again.
© If static electricity is pronounced, it is
recommended that you operate the unit using the
remote controller.
e Static electricity affected the unit when the air
was dry, such as in winter.
Control was not possible
regardless of what operation
switch was pressed.
© Consult page 8 —
10, 31
—
35 and perform
connections correctly.
¢ Press the MUTING switch to cancel the MUTING
effect.
© Press the switch again to the OFF position.
© Press the SPEAKERS switch to turn ON.
© Raise volume.
© Connect wires to terminals securely.
* Connections are incorrect.
No sound is produced, even
when the INPUT SELECTOR
switch is selected.
¢ The MUTING switch is pressed.
@ TAPE 2 MONITOR switch is in the ON position.
© SPEAKERS switches are turned OFF.
e VOLUME
is turned down.
© Speaker connecting wires are disconnected from
speaker terminals.
© One or both of the input cords are disconnected.
© Connector bars are disconnected.
Rear sound is not produced.
@ SURROUND
MODE switch is OFF position.
REAR SPEAKERS switch is OFF position.
¢ REAR LEVEL control is minimum.
® Connect input cords securely.
© Connect bars securely.
¢ Press the SURROUND MODE or REAR SPEAKERS
switch to correct position.
© Adjust REAR LEVEL control.
¢ Press the REAR BALANCE R or L on the remote
control unit to correct the balance.
© Use the simulated surround mode.
REAR L or R sound is not
¢ REAR BALANCE is incorrect.
produced.
© The sound is monaural.
¢ Consult page 8 —
10, 31
—
35 and perform
connections correctly.
¢ Set correctly.
No picture is produced, even
® Connections are incorrect.
when the INPUT SELECTOR
switch is selected.
¢ The VIDEO SIGNAL SELECTOR is not set
properly.
¢ The VCR and the selected INPUT SELECTOR
switch are not correct.
© Press the correct switch.
© Station has not been tuned in to correct
¢ Tune the station in correctly.
frequency.
¢ Antenna has not been connected or has become
disconnected.
FM reception
¢ Accessory T-type antenna remains bundled up
or it is not pointing in right direction.
¢ Weak broadcasting station signals.
High noise level.
® Connect the antenna securely.
¢ Stretch both end of antenna taut and locate
direction yielding optimum reception.
© Replace accessory T-type antenna with outdoor
FM antenna.
AM reception
¢ AM loop antenna is not pointing in right direction.
¢ Change the AM loop antenna's direction and find
a position where reception is improved.
© Erect outdoor AM antenna or connect ground
wire.
¢ Stop using appliances generating noise or remove
them from vicinity of stereo equipment.
* Weak broadcasting station signals.
© Noise being picked up from this unit and other
equipment (especially electrical appliances using
motor or fluorescent lights).
¢ Separate the loop antenna from the unit by some
distance.
© Input signals are not strong enough.
© (FM) If the T-type antenna is being used, change
to an outdoor antenna.
No auto stop.
45
<ARB1234>