Pioneer GM-6000F Manual do Proprietário - Página 2

Procurar online ou descarregar pdf Manual do Proprietário para Amplificador Pioneer GM-6000F. Pioneer GM-6000F 6 páginas. Bridgeable four-channel power amplifier
Também para Pioneer GM-6000F: Manual do Proprietário (9 páginas)

Imprimir página

Connecting the Unit

CAUTION

• Disconnect the negative (–) terminal of the battery

• Make sure that wires will not interfere with mov-

to avoid the risk of short-circuit and damage to

ing parts of the vehicle, such as the gearshift,

the unit.

handbrake or seat sliding mechanism.

• Secure the wiring with cable clamps or adhesive

• Do not shorten any wires. Otherwise the protec-

tape. To protect the wiring, wrap adhesive tape

tion circuit may fail to work when it should.

around it where they lie against metal parts.

• Never feed power to other equipment by cutting

• Do not route wires where they will get hot, for

the insulation of the power supply wire to tap

example where the heater will blow over them. If

from the wire. The current capacity of the wire

the insulation heats up, it may become damaged,

will be exceeded, causing overheating.

resulting in a short-circuit through the vehicle

• Never replace the fuse with one of greater value

body.

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

CAUTION:

To prevent damage and/or injury

• Do not ground the speaker wire directly or con-

• Speakers to be connected to the amplifier should

nect a negative (–) lead wire for several speakers.

conform with the standards listed below. If they

• This unit is for vehicles with a 12-volt battery and

do not conform, they may catch fire, emit smoke

negative grounding. Before installing it in a recre-

or become damaged. The speaker impedance must

ational vehicle, truck or bus, check the battery

be 2 to 8 ohms. But in case of two-channel and

voltage.

other bridge connections, the speaker impedance

• If the car stereo is kept on for a long time while

must be 4 to 8 ohms.

the engine is at rest or idling, the battery may go

• Install and route the separately sold battery wire

dead. Turn the car stereo off when the engine is at

as far away as possible from the speaker wires.

rest or idling.

Install and route the separately sold battery wire,

• If the system remote control wire of the amplifier

ground wire, speaker wires and the amplifier as

is connected to the power terminal through the

far away as possible from the antenna, antenna

ignition switch (12 V DC), the amplifier will

cable and tuner.

always be on when the ignition is on— regardless

• Cords for this product and those for other prod-

of whether the car stereo is on or off. Because of

ucts may be different colors even if they have the

this, the battery could go dead if the engine is at

same function. When connecting this product to

rest or idling.

another product, refer to the supplied Installation

manuals of both products and connect cords that

have the same function.

Speaker Channel

Speaker Type

Power

Subwoofer

Nominal input: Min. 60 W

Four-channel

Other than subwoofer

Max. input: Min. 100 W

Subwoofer

Nominal input: Min. 155 W

Two-channel

Other than subwoofer

Max. input: Min. 240 W

Three-channel

Subwoofer

Nominal input: Min. 60 W

Speaker output A

Other than subwoofer

Max. input: Min. 100 W

Three-channel

Subwoofer

Nominal input: Min. 155 W

Speaker output B

Other than subwoofer

Max. input: Min. 240 W

Connection Diagram

Fuse (30 A)

Special red battery wire [RD-223] (sold separately)

Grommet

After making all other connections at the amplifier,

connect the battery wire terminal of the amplifier to

the positive (+) terminal of the battery.

Fuse (30 A)

Ground wire (black) [RD-223] (sold separately)

Connect to metal body or chassis.

Amplifier with

RCA input

RCA input jacks

Connecting wires with RCA pin

plugs (sold separately).

Car stereo with

RCA output jacks

External Output

If only one input plug is used, do not

connect anything to RCA input jack B.

Input Select Switch

For two-channel input, slide this switch

to the left. For four-channel input, slide

this switch to the right.

Front side

RCA input jack B

RCA output jack

RCA input jack A

Connecting wires with RCA pin

plugs (sold separately).

Back side

× 2

Fuse (20 A)

Speaker output terminal

System remote control wire (sold separately)

See the "Connecting the

Connect the male terminal of this wire to the system remote control

Speakers and Input wires"

terminal of the car stereo (SYSTEM REMOTE CONTROL). The female

section for speaker connec-

terminal can be connected to the auto-antenna relay control terminal. If the

tion instructions.

car stereo does not have a system remote control terminal, connect the

male terminal to the power terminal through the ignition switch.

Connecting the Power Terminal

4. Connect the wires to the terminal.

• Fix the wires securely with the terminal

• Always use the special red battery and ground

screws.

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

GND terminal

terminal (+) and the ground wire to the car body.

Power terminal

System remote

control terminal

1. Pass the battery wire from the

engine compartment to the interior

System remote

of the vehicle.

control wire

• After making all other connections to the

amplifier, connect the battery wire terminal of

the amplifier to the positive (+) terminal of

the battery.

Engine

Fuse (30 A)

compart-

Interior of

ment

the vehicle

Battery wire

Fuse (30 A)

Drill a 14 mm

Positive terminal

hole into the

vehicle body.

Insert the O-ring rubber

grommet into the vehicle

body.

2. Twist the battery wire, ground wire

and system remote control wire.

Twist

3. Attach lugs to wire ends. Lugs not

supplied.

• Use pliers, etc., to crimp lugs to wires.

Lug

Ground wire

Lug

Battery wire

Connecting the Speaker Output

3. Connect the speaker wires to the

speaker output terminals.

Terminals

• Fix the speaker wires securely with the termi-

nal screws.

1. Expose the end of the speaker wires

using nippers or a cutter by about

10 mm and twist.

Twist

10 mm

Ground wire

Speaker

output

2. Attach lugs to speaker wire ends.

terminal

Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

Lug

Speaker wire

Terminal screw

Speaker wire