Pioneer GM-X304 Manual de serviço - Página 16
Procurar online ou descarregar pdf Manual de serviço para Amplificador Pioneer GM-X304. Pioneer GM-X304 17 páginas. Bridgeable four-channel power amplifier
Também para Pioneer GM-X304: Manual de serviço (18 páginas)
GM-xX404,x304
Connecting the Unit
A\ CAUTION
Remove the negative (-) terminal of the
battery to avoid the risk of short-circuit
and damage to the unit.
Secure the wiring with cable clamps or
adhesive tape. To protect the wiring,
wrap adhesive tape around them where
they lie against metal parts.
Do not route wires where they will get
hot, for example where the heater will
blow over them. If the insulation heats
up, it may become damaged, resulting in
8 short-circuit through the vehicle body.
Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, handbrake or seat sliding
mechanism.
Do not shorten any wires. Otherwise the
protection circuit may fail to work when it
should.
Never feed power to other equipment by
cutting the insulation of the power supply
wire to tap from the wire. The current
capacity of the wire will be exceeded,
causing overheating.
Be sure to use the special red battery wire
supplied with the amplifier and connect
directly to the battery. Use the supplied
black ground wire and connect to the
vehicle body. (The supplied special red
battery and ground wires are designed so
that the amplifier can be connected
safely.)
{18} Blue
Connect the male terminal of this wire
to the blue wire of the car stereo
(system control terminal). The female
terminal can be connected to the auto-
antenna relay control terminal.
lf the car stereo does not have a
system remote control terminal,
connect the male terminal to the power
terminal through the ignition switch.
[19] Speaker output terminals
22
See the "Connecting the Speakers and
Input wires" section for speaker con-
nection instructions.
@ To prevent damage
.
Do not ground the speaker lead wire
directly or connect a negative (—) lead
wire for several speakers.
Speakers to be connected to the amplifier
should conform with the standards listed
below. Otherwise damage will be caused
to the speaker. The speaker impedance
must be 2 to 8 ohms.
This unit is for vehicles with a 12-volt
battery and negative grounding. Before
installing it in a recreational vehicle, truck,
or bus, check the battery voltage.
* Install and route the sold separately
special red battery wire supplied with the
amplifier as faraway as possible from the
speaker wires. Install and route the
battery wire, ground wire, speaker wires,
and the amplifier as faraway as possible
| Channei
| Type
Four-
channel
Other than
sub-woofer
Two-
channel
Other than
sub-woofer
Three-
channel
Speaker
output A
Nominal input:
Min. 30 W
Max. input:
Min. 60 W
Nominal input:
Min. 70W
Max. input:
Min. 140 W
Three-
channel
Speaker
output B
Connecting the Power Terminal
Be sure to use the special red battery wire
supplied with the amplifier and connect
directly to the battery. Use the supplied
black ground wire and connect to the
vehicle body. (The supplied special red
battery and ground wires are designed so
that the amplifier can be connected
safely.)
Pass the special red battery wire from the
engine compartment to the interior of the
vehicle.
Fuse
:
-
(30 A)
Engine
Interior of
compart-
the vehicle
ment
"i
*
Special red
battery wire
After making all
other connections
at the amplifier,
connect the battery
wire terminal of the
Drill an 8-mm
hole into the
vehicle body.
insert the
O-ring rubber
grommet into
the vehicle body.
amplifier to the
positive (+) terminal
of the battery.
Fig. 22
Nominal input:
Other than
Max. input:
sub-woofer | Min. 60 W
Nominal input:
Other than
Max. input:
sub-woofer | Min. 140 W
from the antenna, antenna cable and
tuner.
(Fig. 20)
{8] Special red battery wire
After making all other connections
at the amplifier, connect the battery
lead terminal of the amplifier to the
positive (+) terminal of the battery.
Ground wire (black)
Connect to metal body or chassis.
[10] Fuse (Special red battery power wire:
30 A, Amplifier: 25 A)
{11] Grommet
[12] Car stereo with RCA output pin jacks
[13] External Output
For details on how to connect to RCA
input jacks A and B, see the
"Connecting the Speakers and Input
wires" section.
If only one input pin plug, do not
connect anything to RCA input jack B.
[14] White
[15] Red
(16] Connecting wires with RCA pin plugs
(sold separately)
[17] RCA input pin jack A, B
[9]
Connect the special red battery wire to thr
POWER terminal (+), and the black ground
wire to the GND terminal (-).
POWER
Terminal
terminal
screw
Terminal
GND
rs
screw
terminal
i
ae
'
Ground wire
(black)
Special red
battery wire
Fig. 23
Fig. 24
+ Securely fasten the special red battery
lead and the ground wires with terminal
screws.
Connecting the Speakers and Input
wires
The speaker output mode can be four-
channel, three-channel (stereo + mono) or
two-channel (stereo, mono). Connect the
speakers according to figures on following
pages.