Pioneer GM-X562 Manual do Proprietário - Página 2

Procurar online ou descarregar pdf Manual do Proprietário para Amplificador Pioneer GM-X562. Pioneer GM-X562 6 páginas. Bridgeable power amplifier
Também para Pioneer GM-X562: Manual do Proprietário (8 páginas), Manual do Proprietário (17 páginas)

Pioneer GM-X562 Manual do Proprietário

Connecting the Unit

CAUTION
• Disconnect the negative (–) terminal of the battery
• Make sure that wires will not interfere with mov-
to avoid the risk of short-circuit and damage to
ing parts of the vehicle, such as the gearshift,
the unit.
handbrake or seat sliding mechanism.
• Secure the wiring with cable clamps or adhesive
• Do not shorten any wires. Otherwise the protec-
tape. To protect the wiring, wrap adhesive tape
tion circuit may fail to work when it should.
around it where they lie against metal parts.
• Never feed power to other equipment by cutting
• Do not route wires where they will get hot, for
the insulation of the power supply wire to tap
example where the heater will blow over them. If
from the wire. The current capacity of the wire
the insulation heats up, it may become damaged,
will be exceeded, causing overheating.
resulting in a short-circuit through the vehicle
body.
To prevent damage
• Do not ground the speaker wire directly or con-
• Speakers to be connected to the amplifier should
nect a negative (–) lead wire for several speakers.
conform with the standards listed below. If they
• This unit is for vehicles with a 12-volt battery and
do not conform, they may catch fire, emit smoke
negative grounding. Before installing it in a recre-
or become damaged. The speaker impedance must
ational vehicle, truck or bus, check the battery
be 2 to 8 ohms for stereo connection, and 4 to 8
voltage.
ohms for monaural and other bridge connection.
• If the car stereo is kept on for a long time while
• Install and route the separately sold battery wire
the engine is at rest or idling, the battery may go
as far away as possible from the speaker wires.
dead. Turn the car stereo off when the engine is at
Install and route the separately sold battery wire,
rest or idling.
ground wire, speaker wires and the amplifier as
• If the system remote control wire of the amplifier
far away as possible from the antenna, antenna
is connected to the power terminal through the
cable and tuner.
ignition switch (12 V DC), the amplifier will
• Cords for this product and those for other prod-
always be on when the ignition is on— regardless
ucts may be different colors even if they have the
of whether the car stereo is on or off. Because of
same function. When connecting this product to
this, the battery could go dead if the engine is at
another product, refer to the supplied Installation
rest or idling.
manuals of both products and connect cords that
have the same function.
Speaker Channel
Speaker Type
Power
Subwoofer
Nominal input: Min. 80 W
Two-channel
Other than subwoofer
Max. input: Min. 130 W
Subwoofer
Nominal input: Min. 210 W
One-channel
Other than subwoofer
Max. input: Min. 300 W
Connection Diagram
Fuse (30 A)
Special red battery wire [RD-223] (sold separately)
After making all other connections at the amplifier,
Grommet
connect the battery wire terminal of the amplifier to
the positive (+) terminal of the battery.
Fuse (30 A)
Ground wire (black) [RD-223] (sold separately)
Connect to metal body or chassis.
Connecting wires with RCA
pin plugs (sold separately).
Car stereo with
RCA output jacks
External Output
Front side
RCA input jack
Speaker input terminal
See the "Using the
Speaker Input" section.
Back side
Fuse (25 A)
Speaker output terminal
System remote control wire (sold separately)
See the "Connecting the
Connect the male terminal of this wire to the system remote control
Speaker wires" section
terminal of the car stereo (SYSTEM REMOTE CONTROL). The
for speaker connection
female terminal can be connected to the auto-antenna relay control
instructions.
terminal. If the car stereo does not have a system remote control ter-
minal, connect the male terminal to the power terminal through the
ignition switch.
4. Connect the wires to the terminal.
Connecting the Power Terminal
• Fix the wires securely with the terminal
• Always use the special red battery and ground
screws.
wire [RD-223], which is sold separately. Connect
GND terminal
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
Power terminal
System remote
control terminal
1. Pass the battery wire from the
engine compartment to the interior
of the vehicle.
• After making all other connections to the
amplifier, connect the battery wire terminal of
the amplifier to the positive (+) terminal of
the battery.
Engine
Fuse (30 A)
compart-
Interior of
the vehicle
ment
Battery wire
Fuse (30 A)
Connecting the Speaker Output
Drill a 14 mm
Positive terminal
hole into the
Terminals
vehicle body.
Insert the O-ring rubber
grommet into the vehicle
body.
1. Expose the end of the speaker wires
using nippers or a cutter by about
10 mm and twist.
2. Twist the battery wire, ground wire
and system remote control wire.
Twist
10 mm
2. Attach lugs to speaker wire ends.
Lugs not supplied.
3. Attach lugs to wire ends. Lugs not
• Use pliers, etc., to crimp lugs to wires.
supplied.
Lug
• Use pliers, etc., to crimp lugs to wires.
Lug
Speaker wire
Ground wire
Lug
Battery wire
3. Connect the speaker wires to the
Using the Speaker Input
speaker output terminals.
Connect the car stereo speaker output
• Connect the speaker wires, passing them
wires to the amplifier using the supplied
through the terminal cover.
speaker input connector.
• Fix the speaker wires securely with the termi-
• Do not connect both the RCA input and the
nal screws.
Terminal screw
7 Connections when using the speaker
System remote
input
control wire
Ground wire
Terminal cover
Speaker
output
terminal
Speaker wire
4. Push on the terminal cover.
Twist
speaker input at the same time.
Car Stereo
Speaker output
White/black:
Gray/black:
Left ≠
Right ≠
White:
Gray:
Left +
Right +
Speaker input connector
To speaker input terminal of
this unit.