Pioneer SA-V210 Manual de Instruções - Página 5

Procurar online ou descarregar pdf Manual de Instruções para Amplificador Pioneer SA-V210. Pioneer SA-V210 8 páginas. Stereo mixing amplifier
Também para Pioneer SA-V210: Manual de serviço (23 páginas)

Imprimir página

PANEL FACILITIES

: Normal position

(When neither LASERDISC

nor VCR signal is input.)

If "CABLE"

is automatically

selected

even

though

TAPE/AUX"

signal is being played , set to this position 7

L" to select "TAPE/AUX."

(When neither LASERDISC nor VCR signal is input.)

if AUTO INPUT selector remains at "TAPE/AUX" even

though

TAPE/AUX

finishes

its playback,

set

to this

position "H" to select "CABLE."

7 TAPE/AUX VOLUME

control

Controls

the input sound

level

of devices

connected

to the

TAPE/AUX input jacks. This control is normally centered but should

be adjust for LASERDISC.

8) TAPE/AUX MODE switch

This switch is used to select audio modes (MONO/STEREO) of

components connected to the TAPE/AUX input jacks, Connect 4

component with monophonic audio output either to "'L'' or RY

AUDIO INPUT jack and set this switch to "MONO."

@ VISUAL

INPUT jacks

WM 1 LASERDISC

Connect to the VIDEO OUT jack of the LD player.

9.2 VCRICAMERA

Connect to the VIDEO OUTPUT jack of the VCR or TV camera.

1 VISUAL OUTPUT jacks

m1-3

Jacks

for.connection

to the VIDEO

INPUT

jacks of TV

monitors (maximum three monitors).

Wi VCR/CAMERA

ONLY

Signats input to the "VCR/CAMERA" VISUAL INPUT jack

of the SA-V210 will always be output. By connecting to a

TV monitor, you can monitor a VCR or TV camera.

{? SPEAKERS terminals

Two

speaker

systems

(A and

B) can

be connected.

For

details, refer to "CONNECTIONS" on page 3.

* Always connect the plus (+) and minus (—) wires of the

speakers to the speaker terminals of the same polarity. A

polarity error can cause unnatural sound.

13 MIC input jacks 1,2,3

Microphones cannot be connected directly to the SA-V210.

When

placing

the

SA-V210

into a rack

with

MIC

cords,

connect the MIC cords of the rack.

When using microphones

with key control remote switch connected to MIC

4 and 2,

connect the control cords to the KEY

CONTROLLER jacks.

NOTE:

14 AUDIO OUTPUT MONITOR

L + R jack

The

L and

R audio

signals input to the audio

input jacks

49 AUDIO OUTPUT jacks

These jacks are used to output the L and R audio signals to the audio

input jacks (LASERDISC, VCR, CABLE, TAPE/AUX).of this unit.

16 HOWLING

CUT switch

In case of howling, set this switch to "ON."

d? TAPE REC jacks

Connect to the REC

(INPUT] jacks of a cassette deck.

Mic

mixing recording will be possible, because signals. processed

with microphone mixing are output.

When "TAPE/AUX" or "CABLE" has been selected, no sound

can be heard.

48 KEY CONTROLLER AUTO RETURN

switch

ON —

When

a song

is finished,

the

key

controller

will

automatically return to the standard key (4).

GFF —

The key will only change by key control operation.

49: KEY CONTROLLER

REMOTE

CONTROL

jack

commander.)

be remote-controlied.

40 GND (Ground) terminal

Always

ground this unit to prevent electrical shock

and to

avoid generating interference or noise in other equipment.

@) Power cord

FRONT PANEL

1) POWER switch (HZ OFF,

a ON)

'2; MAIN VOLUME control

'3; MUSIC control

Controls

the

volume

equipments

connected

the

LASERDISC,

VCR,

CABLE and TAPE/AUX

jacks on the rear

panel. Normally, keep the MAIN VOLUME

control near the 5

~ 7 position and use the MUSIC control to adjust the volume

of the music source.

4) BALANCE control

Adjusts the balance

between

the sound

from the left and

right.

)» MUSIC. TONE controls

These contro! the tones (BASS/TREBLE) of the music source.

"€ MIC ECHO control