Pioneer VSA-1000 Manual de Instruções - Página 31

Procurar online ou descarregar pdf Manual de Instruções para Amplificador Pioneer VSA-1000. Pioneer VSA-1000 35 páginas. Av digital surround amplifier
Também para Pioneer VSA-1000: Manual de Instruções (35 páginas)

Imprimir página

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the

points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used.

If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer

to carry out repair work.

Problem

Probable cause

Remedy

No power.

* The power plug is not inserted in the wall socket. | ® Plug into the wall socket.

* It is plugged into the power outlet of another

¢ Turn on the power to other appliances.

appliance which is switched off.

No sound.

* The MUTING

(—.%) switch is on.

¢ Switch the MUTING

(— 0) off.

¢ The connecting cord plugs are incorrectly

* Check the connections.

attached to the jacks or connected to the wrong

jacks.

* The jacks or plugs are dirty.

* Clean the jacks and plugs.

e SPEAKER

switches are turned OFF.

¢ Press the SPEAKER switch to turn ON.

¢ The connector bars of the PRE OUT jacks or

* Connect the connector bars. (Refer to page 16)

POWER

AMP IN jacks are disconnected.

In cases other

¢ The TAPE 2/DAT 2 MONITOR

is ON.

* Set the switch to OFF.

than Tape 2.

* The input selector switch setting is not

* Change the switch correctly.

appropriate for the source selected.

¢ There is a mistake in the operation of another

¢ Refer to the instruction manuals of other

component.

components being employed.

In the case

* The TAPE 2/DAT 2 MONITOR

is set to OFF.

¢ Set the switch to ON.

of Tape 2.

* Incorrect operation of the tape deck.

¢ Refer to the tape deck instruction manual.

No picture.

¢ The connecting cord is not firmly plugged in to

ie Check the connections.

the jacks, or it is attached to the wrong jacks.

* The jacks or plugs are dirty.

* Clean the jacks and plugs.

¢ The input selector switch is in the wrong position. | * Change the switch correctly.

® The VIDEO ADAPTOR

switch is ON.

* Set the switch to OFF.

* Other components are not being operated

* Refer to the instruction manuals of other

correctly.

components being employed.

—+—

Sound from only one speaker.

* The connecting cord or speaker cord is loose.

¢ Check the connections.

* The balance adjustment is incorrect.

* Press the left and right balance switches at the

same time to reach the center position.

Recording on tape is impossible. Te

Incorrect operation of the cassette deck.

¢ Refer to the cassette deck instruction manual.

Copying of tapes is impossible.

* Incorrect operation of the cassette deck.

* Refer to the cassette deck instruction manual.

There is no surround sound.

*® The surround switch is OFF.

® Select the surround mode with the SURROUND

MODE switch.

* The input sound is mono but the mode is

* Switch ON the SIMULATED

SURROUND.

STUDIO, STADIUM

or DOLBY PRO LOGIC

SURROUND.

* The front and rear speakers are connected in

¢ Check that the connections are correct.

reverse.

* The input selector switch is not appropriate for

* Change the switch correctly.

the component playing.

Sia,

The remote

control unit does

Batteries dead

or no batteries in remote

control

¢ Insert battery. Or change to new

battery.

not work.

unit.

* Poor angle or too great a distance from the

¢ Use within seven meters and within a 30 degrees

remote sensor window.

angle left or right of the remote sensor window.

¢ There is an obstacle between you and the

* Change your position or move the obstacle.

remote sensor window.