Pioneer VSA-700 Manual - Página 8

Procurar online ou descarregar pdf Manual para Amplificador Pioneer VSA-700. Pioneer VSA-700 30 páginas. Av digital surround amplifier

Imprimir página

FRONT PANEL FACILITIES

@ PHONES Terminal

Connect the plug of a pair of headphones. When listening

through the headphones only, turn both SPEAKERS switches

OFF.

@ DISPLAY Section

Shows the unit condition after each switch operation.

Shows the surround mode.

Lights up when the VCR MODE selector switch is set to

MONO.

Shows the delay time set with the DELAY TIME switch.

Shows the selected ACOUSTIC MEMORY.

Lights up when the MUTING switch is turned on.

Lights up when the VIDEO ADAPTER switch is turned on.

Shows the component selected with the VIDEO SIGNAL

SELECTOR switch.

Shows the name of the component selected with the INPUT

SELECTOR switches.

Lights up when the SIMULATED STEREO and VCR NOISE

FILTER switches are turned on.

@®

Oo O © O©@800

Normally shows left/right output level. After operating the

TREBLE, BASS or ACOUSTIC MEMORY SELECT switch,

it shows the TREBLE

and BASS settings. After a few

seconds it returns to the OUTPUT level indication.

Normally

shows

the volume/balance

setting.

When

operating one of the SURROUND VOLUME switches with

the surround function activated, it shows the surround

volume. When setting the sleep timer function with the

remote control unit, it shows the sleep time. When adjusting

the SURROUND BALANCE with the remote control unit,

it shows the surround balance setting.

@ ACOUSTIC MEMORY Switches

(SELECT/MEMORY)

You can store up to three BASS and TREBLE tone settings in

memory.

MEMORY:

Press this switch to store in memory.

SELECT:

Tone setting changes as follows when pressing this switch

repeatedly:

pPrFLAT -» LOUDNESS -»Memory A -» Memory B -»Memory C 7

FLAT:

Flat tone characteristics.

LOUDNESS:

Low and high frequencies are emphasized. Use this setting to

obtain a full-bodied sound when listening at low volume levels.

How to Use the Acoustic Memory

Choose the desired memory address (A, B or C) with the

ACOUSTIC SELECT switch.

Adjust tone with the BASS and TREBLE controls.

Press the MEMORY switch. The indicator of the selected

memory flashes and the setting is memorized.

¢ This will store the first tone setting in memory. Repeat

the procedure to store the remaining two.

e To recall

a memorized

tone

setting, choose

the

corresponding

memory

address with the SELECT

switch.

Notes on the Memory Function

e As long as the power cord is connected to an outlet, the

memory contents are retained, when setting the power

switch to the STANDBY position. Even if you disconnect the

power cord, the back-up condenser will supply enough

power to protect the memory contents for about two weeks.

¢ When the memory has become erased it has to be preset

again.

@ VIDEO ADAPTOR Switch

Press to play back a video source through the component

connected to the VIDEO ADAPTOR terminals.

@ VCR NOISE FILTER Switch

Use'this switch when playing back video tapes containing too

much noise.

It functions when the VCR 1 or VCR 2 inputs are selected.

NOTE:

This function is cancelled when DAT/TAPE 1 or TAPE 2 are

selected.

VCR MODE

Selector Switch (VCR MODE)

Set this switch to ON, when using a VCR with monaural audio

output.

It functions when the VCR 1 or VCR 2 inputs are selected.

NOTE:

This function is cancelled when DAT/TAPE 1 or TAPE 2 are

selected.

@ DELAY TIME Switch

Switches the surround delay time in three steps.

For DOLBY SURROUND

20 mS is standard.

pes ms >» 20 mS » 30 mS 4

® SIMULATED STEREO Switch

This switch gives monaural sources a stereo-like effect.