Pioneer DEH-1700 Manual de instalação

Procurar online ou descarregar pdf Manual de instalação para Leitor de CD Pioneer DEH-1700. Pioneer DEH-1700 6 páginas. High power cd player with fm/am tuner
Também para Pioneer DEH-1700: Manual de operação (46 páginas), Manual de operação (25 páginas), Manual do Proprietário (46 páginas)

Imprimir página

DEH-1700

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Los colores de los cables este producto se conforman

con el código de colores CEMA.

Printed in Thailand

Imprimé en Thaïlande

<CRD3907-A/N> UC

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

• When this product's source is switched ON, a con-

negative grounding. Before installing it in a recre-

trol signal is output through the blue/white lead.

ational vehicle, truck or bus, check the battery

Connect to an external power amp's system remote

voltage.

control or the car's Auto-antenna relay control ter-

• To avoid shorts in the electrical system, be sure to

minal (max. 300 mA 12 V DC). If the car features

disconnect the ≠ battery cable before beginning

a glass antenna, connect to the antenna booster

installation.

power supply terminal.

• Refer to the owner's manual for details on con-

• When an external power amp is being used with

necting the power amp and other units, then make

this system, be sure not to connect the blue/white

connections correctly.

lead to the amp's power terminal. Likewise, do not

• Secure the wiring with cable clamps or adhesive

connect the blue/white lead to the power terminal

tape. To protect the wiring, wrap adhesive tape

of the auto-antenna. Such connection could cause

around them where they lie against metal parts.

excessive current drain and malfunction.

• Route and secure all wiring so it cannot touch any

• To avoid a short-circuit, cover the disconnected

moving parts, such as the gear shift, handbrake and

lead with insulating tape. Insulate the unused

seat rails. Do not route wiring in places that get

speaker leads without fail. There is a possibility of

hot, such as near the heater outlet. If the insulation

a short-circuit if the leads are not insulated.

of the wiring melts or gets torn, there is a danger of

• If this unit is installed in a vehicle that does not

the wiring short-circuiting to the vehicle body.

have an ACC (accessory) position on the ignition

• Don't pass the yellow lead through a hole into the

switch, the red lead of the unit should be connected

engine compartment to connect to the battery. This

to a terminal coupled with ignition switch ON/OFF

will damage the lead insulation and cause a very

operations. If this is not done, the vehicle battery

dangerous short.

may be drained when you are away from the vehi-

• Do not shorten any leads. If you do, the protection

cle for several hours. (Fig. 1)

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a fuse

of the rating prescribed on this unit.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

ACC position

No ACC position

the left and right ≠ speaker leads are common.

If you ground the products together and the ground

becomes detached, there is a risk of damage to the

products or fire.

• The black lead is ground. Please ground this lead

• Cords for this product and those for other prod-

separately from the ground of high-current prod-

ucts may be different colors even if they have the

ucts such as power amps.

same function. When connecting this product to

If you ground the products together and the ground

another product, refer to the supplied manuals of

becomes detached, there is a risk of damage to the

both products and connect cords that have the

products or fire.

same function.

• Speakers connected to this unit must be high-

power with minimum rating of 45 W and imped-

ance of 4 to 8 ohms. Connecting speakers with out-

put and/or impedance values other than those

noted here may result in the speakers catching fire,

emitting smoke, or becoming damaged.

This Product

Rear output

Antenna jack

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Red

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Fig. 1

Black (ground)

To vehicle (metal) body.

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Perform these connections when using

the optional amplifier.

Connecting cords

with RCA pin plugs

Fuse

(sold separately)

Blue/white

To system control terminal of the power amp

or Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

System remote control

White

Gray

Front speaker

≠

White/black

Gray/black

Left

Green

Violet

Rear speaker

≠

Green/black

Violet/black

Rear speaker

≠

Power amp

(sold separately)

Front speaker

≠

Right

Rear speaker

≠

Rear speaker

≠

Fig. 2