Pioneer AVH-P4900DVD - DVD Player With LCD Monitor Manual de instalação - Página 4
Procurar online ou descarregar pdf Manual de instalação para Leitor de DVD Pioneer AVH-P4900DVD - DVD Player With LCD Monitor. Pioneer AVH-P4900DVD - DVD Player With LCD Monitor 9 páginas. Av receiver/dvd player
Também para Pioneer AVH-P4900DVD - DVD Player With LCD Monitor: Manual de serviço (9 páginas)
![Pioneer AVH-P4900DVD - DVD Player With LCD Monitor Manual de instalação](/uploads/products/server2/6633501/6633501.png)
Connecting the Units
ENGLISH
When connecting the external video component and the display
Audio input
Video input
External
video
component
(sold separately)
To audio outputs
Audio output
RCA cables
Multi-DVD Player
(sold separately)
(sold separately)
To video output
Video output
Video output
RCA cable
Display with
(sold separately)
RCA input jacks
To video input
• It is necessary to set AV INPUT to VIDEO in SET UP when connecting the external
video component.
• It is necessary to set AV INPUT to M-DVD in SET UP when connecting a multi-DVD
player.
When using a display connected to rear video output
This product's rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.
WARNING:
• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD while
Driving.
Installation
Note:
DIN Front/Rear-mount
• Check all connections and systems before final
installation.
This unit can be properly installed
• Do not use unauthorized parts. The use of unautho-
either from "Front" (conventional DIN
rized parts may cause malfunctions.
Front-mount) or "Rear" (DIN Rear-
• Consult with your dealer if installation requires
mount installation, utilizing threaded
drilling of holes or other modifications of the vehi-
screw holes at the sides of unit chassis).
cle.
For details, refer to the following illus-
• Do not install this unit where:
— it may interfere with operation of the vehicle.
trated installation methods.
— it may cause injury to a passenger as a result
of a sudden stop.
Before installing the unit
• Do not install the display where it may (i) obstruct
the driver's vision, (ii) impair the performance of
• Remove the frame and the hold-
any of the vehicle's operating systems or safety
er. (Fig. 14)
features, including air bags, hazard lamp buttons or
(iii) impair the driver's ability to safely operate the
Pull out to remove the frame and then
vehicle.
loosen the screws (2 × 3 mm) to
• The semiconductor laser will be damaged if it
remove the holder. (When reattaching
overheats. Install this unit away from hot places
the frame, point the side with a groove
such as near the heater outlet.
downwards and attach it.)
• Optimum performance is obtained when the unit is
installed at an angle of less than 30°. (Fig. 12)
30°
Fig. 11
Fig. 12
• The cords must not cover up the area shown in the
figure below. This is necessary to allow the ampli-
fires to radiate freely. (Fig. 13)
Do not close this area.
Fig. 13
DIN Front-mount
Installation with the rubber bush
1. Decide the position of the side
brackets. (Fig. 15)
When installing in a shallow space,
change the position of side brackets. In
this case, stick conceal tape on parts
that protrude from the dashboard.
Side bracket
Flush surface screw (5 × 6 mm)
Holder
Screw (2 × 3 mm)
Frame
Fig. 14
2. Install the unit into the dash-
DIN Rear-mount
board. (Fig. 16)
After inserting the holder into the dash-
Installation using the screw holes on
board, then select the appropriate tabs
the side of the unit
according to the thickness of the dash-
board material and bend them.
• Fastening the unit to the factory
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
Dashboard
182
Rubber bush
53
Screw
Conceal tape
Holder
Side bracket
Screw (2 × 3 mm)
Fig. 15
• After installing the unit into the dash-
board, reattach the frame.
Fig. 16
ENGLISH
radio mounting bracket. (Fig. 17)
(Fig. 18) (Fig. 19)
Dashboard or
Select a position where the screw holes
Console
Factory radio mounting
of the bracket and the screw holes of
bracket
this product become aligned (are fitted),
and tighten the screws at 2 places on
each side. Use any of binding screws (4
× 3 mm), binding screws (5 × 6 mm) or
flush surface screws (5 × 6 mm),
Fastening the front panel
depending on the shape of the screw
If you do not plan to detach the front
holes in the bracket.
*1 Use binding screws (4 × 3 mm) only.
panel, the front panel can be fastened
with supplied screw. (Fig. 20)
* 1
* 1
Fixing screw
Fig. 17
• When installing in a shallow space,
use the following screw holes. In this
case, stick conceal tape on parts that
protrude from the dashboard.
Conceal tape
* 1
* 1
Fig. 18
Screw
Fig. 19
Fig. 20