Pioneer SD-T292 RD/Q1 Manual de Instruções - Página 5

Procurar online ou descarregar pdf Manual de Instruções para Monitor Pioneer SD-T292 RD/Q1. Pioneer SD-T292 RD/Q1 25 páginas. Hi-fi monitor receiver

Imprimir página

Pioneer SD-T292 RD/Q1 Manual de Instruções

FRONT

PANEL

FACILITIES

@ MAIN POWER switch

Turn on this switch before using the remote contro! unit. The red

STANDBY indicator lights to indicate that the main power is on.

When the main power is on, the Hi-Fi Monitor Receiver is in the

power standby mode and no picture will be seen. Turn off the

MAIN POWER switch if the display unit will remain unused for a

Jong time.

@ STANDBY indicator

When the MAIN POWER

switch is pressed, this red indicator

lights up to indicate that the unit is in the power standby mode.

This green indicator lights up when the unit is turned on.

@ MTS AUTO indicator

This indicator lights when MTS broadcast reception is possible.

(See page 17.)

(MTS : Multichannel TV Sound)

@ SYSTEM AUTO indicator

This receiver can automatically identify an incoming signal in ac-

cordance with the TV broadcasting format (NTSC, PAL and

SECAM) used in the receiving area. This indicator lights when the

SYSTEM selector is set to "SYSTEM:AUTO," so the format of

the received signal will be identified, and the receiver will switch

over to that format.

@ Remote sensor

When using the remote control, point its transmitter end toward

this sensor.

@ WHITE

BALANCE control knobs

White balance is the term expressing the quality of the color

white on a white screen. When viewing video camera recordings

with improper white balance, adjust both the red and green con-

trol knobs until you achieve proper color quality.

@ CHANNEL PLAN selector switch

You can set this selector switch to one of three positions in ac-

cordance with the broadcast channel plan used in your area. Set

it as follows:

U.S., CATV: To receive a North American CATV HRC & standard

channel pian broadcast.

U.S., TV: To receive a North American off-the-air U.S. TV chan-

nel plan.

PAL/SECAM AREA: To receive a European (PAL/SECAM) chan-

nel plan broadcast.

@ CHANNEL PRESET buttons

ADD: Press this button to store the currently selected channel in

memory.

ERASE: Press this button to delete the tuned in channel from

memory.

@ CHANNEL selector buttons (—, +)

To select a PRESET channel, press the CHANNEL "+" or "—""

button. To select a higher channel number, press the "+" button.

To select a lower channel number, press the ""—" button.

@ VOLUME control buttons

The sound volume can be judged by the number of colored

arrows (< <<...) displayed on the screen when one of the but-

tons is pressed.

Press the '"—" button to decrease sound volume.

Press the "+" button to increase sound volume.

@ COLOR SYSTEM selector

This switch is used to set the receiver in accordance with the TV

broadcast format used. Each time it is pressed, the set format

will change sequentially. Nomally, set it to "SYSTEM:AUTO." If

you are in a poor reception area, however, confirm the format

used in that area, then set the switch to that position.

NOTE:

ff the SECAM color system is received when the COLOR SYSTEM selec-

tor is set to "SYSTEM: AUTO".

the color on the screen may flicker. In

technical terms, this indicates that the chroma fine burst signals are not

being transmitted from the broadcasting station.

in such 4 case, set the COLOR SYSTEM selector to "SECAM".

@ PICTURE MEMORY SET button

Press this button to memorize the desired picture quality: First,

use the PICTURE adjustment mode selector key on the remote

control unit to adjust the picture quality. Then select PICTURE

MEMORY -1 or -2 and finally press this key. (See page 19.)

@ FUNCTION

selector button

This selector serves two

functions: as an input selector and as a

POWER ON switch when the unit is in the standby mode. If the

selector is pressed after the unit has been set to the standby

mode

(red STANDBY

indicator lights) by pressing the MAIN

POWER switch, the TV will be turned on for operation and auto-

matically set to the input source selected before it was turned

off. Each time this selector is pressed, the input function will be

switched in the following order:

——

TV — VDP

— VIDEO

@ PHONES jack

When a stereo headphone plug (6 mm dia) is inserted here, the

sound will be switched from the speakers to the headphones.