Ariston LL 42 Manual de instruções de instalação e utilização - Página 12
Procurar online ou descarregar pdf Manual de instruções de instalação e utilização para Máquina de lavar loiça Ariston LL 42. Ariston LL 42 16 páginas. Collection 2009
Também para Ariston LL 42: Manual de instruções de instalação e utilização (14 páginas), Especificações (7 páginas), Manual de instruções de instalação e utilização (16 páginas), Manual de instruções de instalação e utilização (13 páginas)
Imprimir página
D
1509)50-4
Your dishwasher has arrived
After having bought or moved your dishwasher to another home, a correct installation ensures that your
dishwasher will operate smoothly and efficiently.
Choose where you want to
install your dishwasher, you
can even place it so that its
sides or back panel are side
by side with furniture or up
against the wall. The
dishwasher is provided with
water supply and drain
hoses, which can be directed
towards the left or right to
facilitate
appropriate
installation.
This dishwasher model can
be built under a single
worktop (please read the
relevant instruction sheet).
Levelling.
Once the appliance is
positioned, adjust the feet by
screwing them in or out
depending on how high you
want it and to level it so that
it is horizontal. Make sure
that it is not inclined more
than 2 degrees. If the
appliance is level, it will help
ensure its correct operation.
Anti-flooding protection
Your dishwasher is provided
with a special system which
blocks the water supply in
the event of leaks inside the
appliance.
Cold water connection.
Connect the cold water
supply hose to a threaded 3/
4 (gas) connector, and
making sure that it is
fastened tightly in place. If
the water hoses are new or
have been out of use for an
extended period of time, let
the water run to make sure it
is clear and free of impurities
before
making
connection. If this precaution
is not taken, the water inlet
could get blocked, causing
damage to your dishwasher
It
is
strongly
recommended to use a new
hose
to
connect
dishwasher to the water
supply line, and the old hose-
set should not be reused.
Asking to specilized shop or
an
authorized
service
technician (see Service)..
& ARISTON DISHWASHER - Instructions for installation and use
All manuals and user guides at all-guides.com
Installation and moving
Hot water connection.
Your dishwasher can be
supplied with hot water from
the mains supply (if you
have a central heating
system with radiators) at a
temperature of no more than
60°C.
In this case, the wash cycle
time will be about 15 minutes
shorter and the wash will be
slightly less effective.
The connection must be
made to hot water supply
following
the
procedures
as
indicated for the cold water
connection.
Drain hose connection.
Fit the drain pipe into a drain
line with a minimum diam-
eter of 4 cm or place it over
the sink. Avoid restricting or
bending it. Use the special
plastic elbow provided (see
figure) to position it in the
best possible way. The part
of the pipe marked with the
letter A should be between
40 and 100 cm above the
ground.
The pipe should not be im-
mersed in water.
the
If the power socket
to which the
-
appliance is
connected is not
compatible with
the plug, replace it
the
with a suitable plug
rather than using
adapters or
multiple plugs as
these could cause
overheating or
burns.
same
those
Electrical connection.
First of all, check that the
mains voltage and frequency
values correspond to those
stated on the rating plate
located on the stainless steel
inner door of the appliance
and that the electrical
system
to
which
dishwasher is connected is
sized for the maximum
current indicated on said
rating plate.
A
Earth: indispensable
safety.
Only now can you plug the
appliance into a socket
provided with an efficient
earth connection (the
system's earthing is a
guarantee of safety provided
for by law, make sure your
system has it).
Attention
- Once the appliance has
been installed, the electrical
plug and socket should re-
main accessible.
- If the power supply cable is
damaged,
it
must
replaced
by
the
manufacturer
or
Technical
Assistance
Service in order to prevent
all potential hazards. (See
Assistance)
- The cable should not be bent
or compressed.
- The Company shall not be
held responsible for any
incidents that occur if these
regulations are not observed.
The special plastic
elbow should be
fastened firmly
onto the wall to
prevent the drain
hose from moving
and allowing water
to spill outside the
drain.
be
the
its