Dinex CARLISLE Turbo-Temp DX1011208 Manual de operação e manutenção - Página 3

Procurar online ou descarregar pdf Manual de operação e manutenção para Carregador de bateria Dinex CARLISLE Turbo-Temp DX1011208. Dinex CARLISLE Turbo-Temp DX1011208 8 páginas.

Imprimir página

CAUTION: Please do not attempt to open the charger or perform

service of any kind. This product can only be serviced by a Dinex

Authorized Service Agent or designated Dinex personnel. Contact

Dinex at 1.888.673.4639 for service information.

CAUTION: Any installation not matching the requirements

discussed in this manual will automatically void the product's

warranty.

INSTALLATION

1. The Turbo•Temp Charger can be installed on top of a flat, level

counter top or shelving, being careful to maintain at least two inches

of clearance on all sides of the charger for cooling. Do not place

over paper or loose material that may inhibit air flow into the bottom

air intakes. Consider the Dinex Induction Stand (Accessory product)

ICSTANDM (Mobile with casters) ICSTAND (Not mobile).

2. The charger must be plugged into a grounded 208V 3-Phase

receptacle. Check rating plate on the charger

to verify correct voltage.

IMPORTANT: Each charger should be connected to its own

dedicated circuit. They should not be connected to circuits sharing

compressors or other heavy current draw devices (i.e. plate heaters,

steam tables, etc.)

3. Do not move the Turbo•Temp Charger when it is electrically

connected.

4. Two grease filters are mounted to the bottom of the unit. Assure

each is seated and free of excessive debris or grease.

OPERATION INSTRUCTIONS

Turbo•Temp Induction System

1. Make sure that your Turbo•Temp Charger is plugged into an

energized circuit as described in the previous section. This should

be a dedicated circuit, not shared with any devices utilizing motors,

compressors, or components requiring a heavy current draw.

User Interface:

LCD

INFO CENTER

POWER

SELECT

POWER key will turn the unit on and off.

SELECT key will be used to reset error conditions, clear informational

messages, and select or set options.

PMS 354 C (Power Button)

PMS 506 C (Select Button)

PMS Process Black C at 90% (Arrows)

PMS 485 C (Line & Temp)

UP/DOWN arrow keys (these are not embossed – just right of the

SELECT key) are used to move among Manager Options in the

OPTIONS menu.

LCD Info Center provides feedback on the status of bases charging

and equipment operation.

2. The Turbo•Temp Charger is turned on by pressing the POWER

button on the left front of the switch panel. The LCD Info Center will

display "Waiting for base..." indicating the Turbo•Temp Charger is

turned on and ready for use.

3. Place a Dinex Smart base on the charger within the positioning rails,

making sure the base is seated flat on the top. The charger will beep

once as it recognizes the base.

4. The LCD Info Center will display "Heating Base" when it begins a

charge. A status bar at the bottom of the screen will continue to fill

in to show the charge process. If the base is removed prior to the

status bar being completely filled the base will not be fully charged

and may result in a lower delivery temperature.

INFORMATION: You will hear three loud "BEEPS" if you remove the

base before it is fully charged.

INFORMATION: To prevent overheating a base, the charger will

not reheat a base until slightly over one hour has elapsed – even

if the base was removed before the initial charge completed.

"Reheat Later" will appear in the LCD if insufficient time has elapsed

between charges.

5. If the phrase "Waiting for base..." still appears after placing a base

on the charger, remove the base and reposition – assuring the base

is seated flat to the top, and within the positioning rails.

6. After the status bar is completely filled the charger will display "Base

Ready" and will beep indicating that base is at full temperature.

Charge time for a base will be approximately 10 seconds. Low

incoming voltage may increase charging time.

INFORMATION: Fluctuations in voltage may affect heating time.

7. If the charger sees no activity for an extended period of time, it will

beep 2 times and go into "Sleep" mode to conserve power. This will

be indicated by the display reading "Power Save. Press any key to

return to previous mode". Press any key to exit "Sleep" mode.

8. Power off the Turbo•Temp Charger by depressing the POWER

button.

MANAGER OPTIONS

Your Turbo•Temp charger can be set to display in English, Spanish, or

French languages. You may also choose to disable information alerts

(see below). These options may be changed through the OPTIONS

menu.

DINEX

POWER

SELECT

1. The unit must be powered down with DINEX in the display. Press

and hold the SELECT key for 7 seconds.

2. Release the SELECT key, and within two seconds, press the

PMS 354 C (Power Button)

PMS 506 C (Select Button)

POWER key once. The OPTIONS menu should now be displayed.

PMS Process Black C at 90% (Arrows)

PMS 485 C (Line & Temp)

SET OPTIONS

Set Language

Ignore Warnings

Reset Defaults

POWER

SELECT

Exit

3. Use the UP/DOWN arrow keys to move the caret symbol (>) to the

desired option, and press SELECT.

4. The "Set Language" and "Ignore Warnings" options will bring up sub-

PMS 354 C (Power Button)

PMS 506 C (Select Button)

menus where you may select the desired mode. "Set Languages"

PMS Process Black C at 90% (Arrows)

PMS 485 C (Line & Temp)

allows you to choose between displaying English, Spanish, or

Turbo•Temp | 3