Ariston FM 81 R IX AUS Folheto de instruções - Página 9
Procurar online ou descarregar pdf Folheto de instruções para Forno Ariston FM 81 R IX AUS. Ariston FM 81 R IX AUS 10 páginas.
![Ariston FM 81 R IX AUS Folheto de instruções](/uploads/products/server2/675693/675693.png)
:ffi]t-ltli
I
il@li
lF-t
-:lll
I
To fasten the oven to the cabinet, open the door of the
oven and fasten it by inserting the 4 wood screws into the
4 holes locate on the Derimeter of the frame.
The panels of the adjacent cabinets must be made of
heat resistant material. In particular, cabinets with a veneer
exlerior must be assembled with glues able to withstand
temperatures of up to 100"C.
In compliance with cunent safety standards, contact with
the electrical parts ofthe oven must not be possible once
it bas been installed.
All parts which ensure safe operation ofthe applianc€ must
not be able to be removed without the use of a tool.
Fastoning the Ovan to the Cabinet (only on a few
models)
1 . Position the 'A' brackets so that they are flush against
the oven support strips (B).
2. Position the cleats (C) on the''A'brackets as shown in
the figure so that the thickness of the sides of the
cabinet, indicated on the cleat, is facing you.
3. Fasten the brackets and the cleats to the edge of the
side of the cabinet using the "O" screws.
4. Fasten the oven to the cabinet usino the screws and
plastic washers (E).
Mountlng a Power Supply Cable
Opening the terminal board:
.
Pullto ooen the @ver of lhe terminal board.
To install the cable, proceed as follo|s:
.
Remove the wire clamp screw and the three contact
scre\ s L-N-+
.
Fasten the wires beneath the heads ofthe screws using
the bllowing color scheme : Blue (N) Brown (L)Yellow-
Green *
.
Fasten the suppy cable in place with the clamp, close the
coverto theterminal box and fasten itwith the'V" screw.
Electrical connec-tion
Ovens with a three-pole power supply cable are designed
to operate with alternated cunent at the supply frequency
and voltage indicated on the data plate (at the bottom of
the oven dashboard).The earthing conductor ofthe cable
is the yellow-green conductor.
Two types of conneciion are provided:
Connection n'1
Connectlng the power supply cable to the mains.
Fit a normalized plug to the cable, which corresponds to
the load indicated on the data plate; il the cooker is
connected directly to the mains, an omnipolar circuiG
breaker with a minimum opening of 3 mm between the
contacts, suitable br the load indicated and complying
with curent directives, must be installed between the
appliance and the mains (the earlhing wire must not be
intenupted by the circuilbreaker).The power supply cable
musl be positioned so that it does not exceed room tem-
perature by 50'C at any point of its length. Before making
the connection check that:
.
the limiter valve and the home system can support
. the power supply system has an efficient earthing
connection which complies with the provisions of
current regulations and the law.
.
there is easy access to the socket or the omnipolar
circuit-breaker once the cooker has been installed.
N.B.: do not use reducers, adapters or shunts as these
could cause heating or burning.
Connection n' 2
Disposing of the plug.
W A R N I N G : T H I S A P P L I A N C E M U S T B E E A R T H E D .
Ensure that befrrre disposing of the plug itsell you make
lhe pins unusable so thai it cannot be accidentally inserted
into a socket. Instructions br connecting cable to an alter-
native plug:
lmportant: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
-Earlfl
-Ncutral
-Llv6
lf the colours of the wires in the mains lead do
correspond with the coloured markings identifying
terminals in your plug, proceed as follows.
Connect Green &Yellow wire to terminal marked "E" or +
or coloured Green or Grgen & Yellow.
Connect Brown wire to terminal marked "L'or coloured
Red. Connect Blue wire to terminal marked "N'or coloured
Black. lf a 13 amp plug (BS 1363) is used it must be fitted
with a 13 amp fuse.
in the plug or adaptor or at the distribution board.lf you
are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
not
Ine