Whirlpool 3358968 Instruções de instalação - Página 4

Procurar online ou descarregar pdf Instruções de instalação para Máquina de lavar roupa Whirlpool 3358968. Whirlpool 3358968 5 páginas.

Imprimir página

DO NOT FORCE EXCESS LENGTH

OF DRAIN HOSE DOWN THE STANDPIPE.

THIS COULD CAUSE SIPHONING.

Before attaching

water inlet

hose, run water through

both faucets

into

a bucket.

This will get rid of particles

the water lines that might clog hoses.

Mark which

is the hot water faucet.

W Attach

bottom

hose (inlet

marked

"H" to hot water faucet.

Attach

top hose (inlet marked

"C") to cold water

faucet.

Tighten couplings

to faucets

hand: then use pliers to make final two-

thirds turn.

Stack two corner posts on

top of each other. Tilt washer

backwards

and insert corner posts 3 inches (7.6 cm)

in from one side of washer as shown.

Repeat with other corner posts on other

side of washer.

Use leas and nuts from

parts package.

Screw nut down to

within

l/2 inch (1.3 cm) of base,

Insert legs into

correct

holes at

each front corner

of washer until

nuts touch

washer.

Do Not

tighten

nuts until

Step 16.

W Tilt washer backward

and

remove

corner post(s). Gently

lower

washer to floor.

Move washer to its final location.

Remove

cardboard

or hardboard

from under

washer.

Tilt washer forward,

raising

back legs 1 inch (2.54 cm) off of floor to

adjust rear self-leveling

legs. Gently

lower

washer to floor. Check levelness

of the

washer by placing

a carpenter's

level on

top of the washer, first side to side; then

front to back.

If washer is not level, screw

the front legs up or down to adjust.

Repeat Step 15.

When washer is level, use wrench

to turn

nuts on front legs up tightly

against

washer

base. If nuts are not tight against

washer

base, the washer may vibrate.

Property

Damage

Secure the drain hose to the tub or

standpipe

with the shipping

strap

removed

from the back of the washer.

Failure to properly

secure drain hose

could

result in water damage.

H Measure

and mark a point

approximately

15 inches (38.1 cm) from

the plug end of the shipping

strap. Cut

the shipping

strap at this point.

Check

that hose is not twisted or kinked

and is securely

in place.

Put "hook" end of drain hose in tub or

standpipe.

Tightly wrap the shipping

strap

around

the drain hose and tub or

standpipe

or inlet hose as shown in

Figures A-C. Push plug into the nearest

hole in the shipping

strap.

If a longer drain hose is needed,

drain

hose (Part No. 388423) and hose

extension

kit (Part No. 285442) are

available

from authorized

parts

distributors.

If drain hose must be

shortened,

use hose kit (Part No. 285442).

Note: If washer

is moved

to adjust drain hose, the

washer

must be leveled

again.

Repeat Steps 1516.

Place cardboard

under the washer

and carefully

move washer

to avoid

damaging

floor covering.

CHECK ELECTRICAL

REQUIREMENTS. BE SURE YOU HAVE

CORRECT ELECTRICAL SUPPLY AND

RECOMMENDED GROUNDING

METHOD.

Check that all parts are now

installed.

See parts list, Pane'1 A. If there is

an extra part, go back through

steps to

see which

step was skipped.

Turn on water faucets

and

check for leaks. Tighten couplings

if there

is leaking.

DO NOT OVERTIGHTEN: this

could

cause damage

to faucet.

H Check that YOU have all of

your tools. Check that the shipping

strap

with 2 cotter

pins and plug was removed

from the back of the washer and used to

secure the drain hose.

and plug into grounded

outlet'.

read the Use and Care Guide to fully

understand

your new washer.

Now start

the washer and allow it to complete

the

regular

cycle.

Congratulatfons!

Keep Installation

Instructions

and

Guide. The instructions

will make

Panel C