Whirlpool 3LCHW9100WQ0 Manual de instruções de instalação - Página 12
Procurar online ou descarregar pdf Manual de instruções de instalação para Máquina de lavar roupa Whirlpool 3LCHW9100WQ0. Whirlpool 3LCHW9100WQ0 48 páginas. Semi-pro front-load washer
Imprimir página
SERVICE ACCESS
CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for 0
vend price without any Special Pricing set-up, and the Coin/Debit
Option must be set to "J._d". If the washer is not in failure mode,
the door must be opened to proceed. Service Access Code
contains 6 steps and some are timed. Using only the three bottom
buttons (numbered 1,2, and 3 from left to right):
1. Press 2 for longer than 2 seconds but less than 10 seconds.
2. Press 1 & 3 together for 2 seconds, then release. Displays S 3.
3. Press 1 & 2 together, then release. Displays S 4.
4. Press 2 & 3 together, then release. Displays S 5.
5. Press 2, then release. Display shows "codE".
6. Wait at least 2 seconds, but not more than 15 seconds, then
press in succession: 3, 2, 1, 3.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15 second delay before it can
be attempted
again.
When the Service Access Code is used, there are 3 options
to exit.
1. From Set-up Code 8, press key #1 for 4 seconds.
2. Wait 2 minutes without touching any keypads (without
diagnostic modes running).
3. Power down the washer, then reapply power.
WASHER
HELP MODE
This mode is entered by pressing the PERM PRESS key pad
while in Set-up option code 2.XX.
In help mode, other display symbols and elements are mapped
to reflect the state of various inputs and outputs as follows:
Display Symbol
Description
Wash
Water sensed at wash level.
*
Low voltage present (below about
90 VAC).
o (Circle above digit)
Door closed.
DOOR LOCKED
Door sensed locked.
COLD
Cold water relay on.
HOT
Hot water relay on.
OR
Door unlock.
AVAILABLE
Drain pump ON.
WASHER CARE
Cleaning the Door Seal/Bellow
1.
2.
Open the washer door and remove any clothing or items from
the washer.
Inspect the colored seal/bellow
between the door opening
and the drum for stained areas. Pull back the seal/bellow
to
inspect all areas under the seal/bellow
and to check for
foreign objects.
_S
A
A. Seal/Bellow
3.
If stained areas are found, wipe down these areas of the
seal/bellow, using the procedure that follows.
a) Mix a dilute solution, using 177 mL (3/4 cup) of liquid
chlorine bleach, and 3.8 L (1 gal.) of warm tap water.
b) Wipe the seal/bellow
area with the dilute solution,
using a damp cloth.
c) Let stand 5 minutes.
d) Wipe down area thoroughly with a dry cloth and let the
washer interior air dry with door open.
IM PORTANT:
•
Wear rubber gloves when cleaning for prolonged
periods.
•
Refer to the bleach manufacturer's
instructions
for proper
use.
Washer
Maintenance
Procedure
This washer has a special cycle that uses higher water volumes in
combination
with liquid chlorine bleach to thoroughly
clean the
inside of the washer.
NOTES:
•
Read these instructions
completely
before beginning the
cleaning process.
•
If necessary, the cleaning cycle may be interrupted by
pressing the DELICATES/KNITS button twice. However, this
will not immediately stop the cycle. The washer will continue
with several rinse and drain steps to ensure that all remaining
bleach is rinsed from the washer.
Begin procedure
1. Open the washer door and remove any clothing or items from
the washer.
2. Use liquid chlorine
bleach:
Open the dispenser drawer and immediately add
160 mL (2/3 cup) of liquid chlorine bleach to the bleach
compartment.
NOTE: Do not add any detergent to this cycle. Use of more
than 160 mL (2/3 cup) of bleach will cause product damage
over time.
3.
4.
Close the washer door and the dispenser drawer.
To start the Clean Washer cycle, first enter "Start Operating
Set-up." Then press and hold DELICATES/KNITS for
1 second. With the entire display flashing, press BRIGHTS.
NOTE: The drum will rotate, then the door will unlock, lock
again, and then the cycle will continue.
•
The washer will not fill, but the drum will rotate while the
washer runs a short sensing cycle. This will take
approximately
3 minutes.
12