Whirlpool AWO/C 0714 Gráfico do programa - Página 2
Procurar online ou descarregar pdf Gráfico do programa para Máquina de lavar roupa Whirlpool AWO/C 0714. Whirlpool AWO/C 0714 2 páginas. 7kg, 1400rpm, 6th sense washing machine with clean +, white wwdc 7410
Também para Whirlpool AWO/C 0714: Manual de instruções de utilização (14 páginas), Manual de instruções de utilização (14 páginas)
Imprimir página
CONSUMPTION DATA
Temperature
Load
Programme
(°C)
(kg)
Cotton/Antibacterial
95
7.0
Cotton *
60
7.0
Cotton *
60
3.5
Cotton *
40
3.5
SuperEco
60
7.0
Synthetics
60
3.0
Synthetics
40
3.0
Delicates
30
1.5
Daily load
40
4.0
Quick wash
30
4.0
Wool
40
1.0
Handwash
40
1.0
Lingerie
30
1.0
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply
will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions
refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also
change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
"Troubleshooting Guide" in your Instructions for Use).
Approximate remaining moisture content (%). After programme and spinning with maximum selectable spin speed, in default programme setting.
*
Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
LOAD LAUNDRY, ADD DETERGENTS
AND SELECT THE PROGRAMME
Load the laundry, close the door and add detergents as
indicated on the front page and as described in the chapter
"Detergent and Additives" in your Instructions for Use.
Turn the programme selector to the desired programme
and temperature. The display shows the programme
duration and the predefined spin speed. The indication lamp
next to the "Start/Pause" button blinks.
If you do not start the programme soon after having
made your choice, the washing machine will switch off
automatically after about a quarter of an hour. To switch the
washing machine on again, turn the programme selector to
"O" and afterwards to the desired programme again.
SELECT ANY DESIRED OPTION
Push the button of any option desired - the respective
indication lamp lights up. If the combination of programme
and additional option(s) is not possible, the indication lights
switch off automatically.
"Clean+" button
• Choose this option if you use an in-wash additive for
stain removal (powder, for example "Vanish") - it will
optimize the additive's efficiency to get better wash
performance and stain removal.
• Use with the maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together
Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
Approx. programme duration
Energy
Water
(hours : minutes)
(kWh)
(l)
without "Rapid"
without "Rapid"
with "Rapid"
74**
2.10
2:10
52
0.91
4:00
40
0.85
3:00
40
0.65
3:00
69
0.84
4:00
50**
1.00
2:15
46
0.70
2:15
60
0.50
0:45
45
0.50
1:00
45
0.40
0:30
60
0.50
0:45
45
0.50
0:40
45
0.40
0:36
with your detergent (only use powder detergent with this
option). Respect the manufacturer's dosing instructions.
• May prolong the programme by up to 15 minutes
• Appropriate for use of stain removers and bleaches
on oxygen basis. Chlorine or perborate bleaches
must not be used!
"Cold wash" button
• Saves energy used for water heating while maintaining
good wash result.
• Recommendable for lightly soiled laundry without stains.
• Make sure that your detergent is suitable for cold
wash temperatures (15 or 20 °C).
• Mainly selectable on the lowest temperature step of
the programmes.
"Intensive rinse" button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
"Easy ironing" button
• Reduces creasing by an increased water quantity and
a very gentle spin.
"Rinse hold" button
• The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing and
prevent colours from changing.
• It is particularly useful if you want to postpone spinning to
a later time, or if you want to drain only.
• The programme stops to "Rinse hold" at the time the
"Rinse hold" lights in the preogramme sequence
indication is on. The "Start/Pause" indicator blinks.
Terminate the "Rinse hold" option:
• Press the "Start/Pause" button; the programme will
%
terminate automatically with the final spin cycle for the
present wash programme.
-
55
• If you do not wish to spin the clothes, turn the
2:30
programme selector to the "Drain" programme and press
the "Start/Pause" button.
***
53
"Spin" button
***
• Every programme has a predefined spin speed.
-
• Press the button to set different spin speed.
0:59
• If spin speed "0" is selected, the final spinning is cancelled
35
but intermediate spin peaks remain during rinse.
0:59
The water is drained out only.
-
"Prewash" button
-
55
• Adds a prewash cycle to the wash programme selected;
-
prolongs the programme by about a quarter of an hour.
-
• Recommended for heavily soiled laundry (e.g. with sand
or granular dirt).
-
• Do not use liquid detergent for the main wash when
-
activating the "Prewash" option.
"Rapid" button
• Enables quicker washing by shortening the programme
duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 95°C.
START DELAY
The "Start delay" allows to run the machine at the
consumer's convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating "Start delay" option.
• Select programme, temperature and options.
• Press the "Start delay" button to select the desired
delay time up to 23 hours.
• Press the "Start/Pause" button. On the display, the start
delay symbol and the dot between hours and minutes
blink. The countdown of the delay time begins.
• The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
• Once having pressed the "Start/Pause" button, the delay
time can be reduced by pressing again the "Start delay"
button.
To cancel the "Start delay"
...before you press the "Start/Pause" button:
• Turn the programme selector to another position or
press the "Reset" button.
...after having pressed the "Start/Pause" button:
• Press the "Start/Pause" button - the start delay time
disappears from the time display.
PROGRAMME START
Open the tap and press the "Start/Pause" button.
The indication lamp next to the "Start/Pause" button lights
up. The programme sequence indicator shows the current
programme phase, running from left to right through Wash,
Rinse, Spin/Drain.
When the laundry load is detected or the programme
duration is updated, the display shows an animation.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer to
"Cancel (Reset) a running programme before the end".
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
"Troubleshooting Guide" in your Instructions for Use.
"Water tap closed": no or not sufficient inlet water.
"Service": failure or malfunction of an electrical
component.
"Clean pump": waste water is not pumped out.
Spin speed on display blinks : unbalance during spinning.
PROGRAMME END
The "Door open" indicator lights up, and the display shows
"End". After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the "O" position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light blinks.
2. Select the new programme, any options and another
spin speed if you want.
3. Press the "Start/Pause" button again.
The new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The "Reset" button cancels a programme before the end.
• Press and hold the "Reset" button for a few seconds.
Any existing water is drained out. It may last some time
until the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA.
W10748556