Whirlpool EL88TRRWS Manual de instruções de instalação - Página 3
Procurar online ou descarregar pdf Manual de instruções de instalação para Frigorífico Whirlpool EL88TRRWS. Whirlpool EL88TRRWS 20 páginas. Trim kit
Também para Whirlpool EL88TRRWS: Manual de dimensões (1 páginas), Manual de utilização e cuidados (24 páginas), Manual de utilização e cuidados do frigorífico (28 páginas), Manual de Energia (2 páginas)
Imprimir página
The SKT60* Trim Kit provides an integrated appearance when
installing an all-refrigerator and upright freezer side by side.
Plan the Installation
Plan your installation using these instructions in conjunction with
the Use & Care Guides provided with the refrigerator and freezer.
IMPORTANT:
For ease in handling and alignment, it is recommended that
two people install the trim kit.
Make sure there is enough area, approximately 7 ft (2.1 m) by
10 ft (3.1 m) to assemble parts on the
Lay a drop cloth on the
the
These instructions are intended as a general guide only and
do not supersede any national or local codes in any way.
Compliance with all local, state or national codes pertaining
to this type of installation should be determined prior to
installation.
Opening Requirements
Make sure the opening is 74 ¹⁄ " (189.2 cm) high by 62
(157.8 cm) wide by 24
" (61.6 cm) deep, as shown.
The inner opening dimensions of the installed trim kit will be
61.31" (155.7 cm) wide by 66.85" (189.7 cm) high.
NOTE: It is possible to make the trim kit t vertical openings that
are less than 74
" (189.2 cm) high. The trim kit can be reduced in
height by 1" (2.54 cm) increments. Each grille extrusion is 1"
(2.54 cm) in height. For each grille extrusion that is not used, 1"
(2.54 cm) must be cut from the base of both the left hand and
right hand side extrusions.
(61.6 cm)
Tools Needed
Assemble the required tools and parts before starting installation.
Read and follow the instructions provided with any of the
required tools listed here. Proper installation is your responsibility.
Tools Needed:
Cordless drill,
" bit
Phillips screwdriver
Flat-blade screwdriver
Socket drive #2 bits
Ratchet
" socket bit
INSTALLATION REQUIREMENTS
r.
to cushion the parts and cover
"
¹⁄
24
"
¹⁄
74
"
(189.2 cm)
¹⁄
62
"
(157.8 cm)
Carpenter's level
Tape measure
Tape (masking or
painters)
Glasses
Parts Supplied
Remove the parts from the trim kit package. Make sure all parts
are included.
IMPORTANT:
Do not use sharp objects to remove packaging materials to
avoid scratching surfaces.
The metal parts can be damaged if they are dropped.
A
B
C
D
E
F
G
Description
(Quantity)
A. Extrusion, Top Trim (1)
B. Extrusion, Grille (6)
C Extrusion Grille-Notched (1)
D. Extrusion, Side Trim - Left (1)
E. Plastic Foam Spacer (1)
F. Gap Filler Assembly (1)
G. Bracket, Front (1)
H. Extrusion, Side Trim - Right (1)
I. Grille, Bottom Assembly (1)
Pan head Phillips screw (7)
Part Number 3-24004-091
5/16 Hex Head screw (4)
Part Number W10204670
Part Number
3-82842-001
3-82840-001
3-82840-002
3-82841-001
3-82841-002
4-82968-001
3-82967-001
2-82975-001
2-82984-001
Countersunk Phillips screw (2)
Part Number 3-24004-159
H
I
3