Whirlpool 30414114 Manual de instruções de instalação - Página 6

Procurar online ou descarregar pdf Manual de instruções de instalação para Frigorífico Whirlpool 30414114. Whirlpool 30414114 20 páginas.

Imprimir página

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator and approved accessories

be provided. Use an outlet that cannot be turned off by a switch.

Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn off Cooling, and then disconnect

the refrigerator from the electrical source. When you have finished,

reconnect the refrigerator to the electrical source and turn on

Cooling. See "Using the Control(s)."

Water Supply Requirements

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call

a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system going to the water inlet valve

of the refrigerator needs to be between 30 and 120 psi

(207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■

Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■

Allow the storage tank on the reverse osmosis system to refill

after heavy usage. The tank capacity could be too low to keep

up with the requirements of the refrigerator.

■

If your refrigerator has a water filter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water

Filtration System."

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■

All installations must meet local plumbing code requirements.

■

Use copper tubing or Whirlpool supply line, Part

Number 8212547RP, and check for leaks.

■

Install copper tubing only in areas where the temperatures

will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

■

Flat-blade screwdriver

⁷⁄₁₆" and ¹⁄₂" Open-end or 2

■

adjustable wrenches

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs

more easily.

Connect to Water Line

Style 1

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long enough

to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold

water pipe near the refrigerator.

IMPORTANT:

■

Make sure it is a cold water pipe.

■

Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning.

Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing.

Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" hole in the cold water pipe

you have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

6. Fasten the shut-off valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal.

Do not overtighten or you may crush the copper tubing.

¹⁄₄" Nut driver

■

¹⁄₄" Drill bit

■

Cordless drill

E. Compression sleeve

F. Shut-off valve

G. Packing nut