Whirlpool WSR25D2RYY00 Instruções para o utilizador - Página 11
Procurar online ou descarregar pdf Instruções para o utilizador para Frigorífico Whirlpool WSR25D2RYY00. Whirlpool WSR25D2RYY00 29 páginas.
Imprimir página•
Has the ice melted around the auger (metal spiral) in the
ice bin? Empty the ice container. Use warm water to melt the
ice if necessary.
Cut Hazard
Use a sturdy glass when dispensing
ice.
Failure to do so can resuR in cuts.
Is the ice dispenser stalling while dispensing "crushed"
ice? Change the ice button from "crushed" to "cubed." If
cubed ice dispenses correctly, depress the button for
"crushed" ice and begin dispensing again.
Has the dispenser arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.
The water dispenser will not operate properly
•
Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."
Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Is the water pressure
at least 30 psi (207 kPa)? The water
pressure to the home determines the flow from the dispenser.
See "Water Supply Requirements."
Kink in the home water source line? Straighten the water
source line.
•
New installation? Flush and fill the water system.
•
Water filter installed
on the refrigerator?
The filter may be
clogged or incorrectly installed.
•
Is a reverse osmosis water filtration
system connected
to
your cold water supply? See "Water Supply Requirements."
Water is leaking from the dispenser
NOTE: One or two drops of water after dispensing is normal.
•
Glass not being held under the dispenser
long enough?
Hold the glass under the dispenser for 2 to 3 seconds after
releasing the dispenser lever/pad.
New installation? Flush the water system. See "Prepare the
Water System" or "Water and Ice Dispensers."
Recently changed water filter? Flush the water system. See
"Prepare the Water System" or "Water and Ice Dispensers."
The dispenser water is not cool enough (on some models)
NOTE: Water from the dispenser is chilled to only 50°F (10°C).
•
New installation?
Allow 24 hours after installation for the
water supply to cool completely.
Recently dispensed large amount of water? Allow 24 hours
for water supply to cool completely.
Water not been recently dispensed? The first glass of water
may not be cool. Discard the first glass of water.
Refrigerator connected to a cold water pipe? Make sure
the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."
ACCESSORIES
To order replacement filters, call 1-800-442-9991
and ask for the
part number listed below or contact your authorized Whirlpool
dealer. In Canada, call 1-800-807-6777.
Stainless
Steel Cleaner and Polish:
Order Part #4396095
Water Filter:
Order Part #W10291030 (P4RFWB)
WATER FILTER CERTIFICATIONS
State of'California
Department of Public Health
Water Treatment Device
Certificate Number
10- 2030
Date Issued:
February
26, 2010
Microbiological
Contaminants
and Turbidity,
Uysts
Organic
Contaminants
Atrazme
Lmdane
;
Toxapli_e
2.4 -D
Rated
Service
Capacity:
200 gal
Rated Service
FIo'_,:
5 gpm
Conditions
of Certifiea|ion:
Do not use where
water is microbiologica]ly
unsafe
or wi{h _ater
oftmknown
quality,
except that _ys/ems cerlified
for cyst reduction
may be used on disinfected
waters
that may comain
filterable
cysts.
11