Whirlpool WGD9151X Dimensões e instalação - Página 2

Procurar online ou descarregar pdf Dimensões e instalação para Secador Whirlpool WGD9151X. Whirlpool WGD9151X 2 páginas. Whirlpool gas dryer dimensions and installation
Também para Whirlpool WGD9151X: Dimensões do produto (1 páginas)

Imprimir página

Whirlpool WGD9151X Dimensões e instalação

INSTALLATION REQUIREMENTS

GAS SUPPLY REQUIREMENTS

Gas supply

This dryer is equipped for use with Natural gas. Dryer can be converted to L.P. gas. When rigid pipe is used it should be 1/2" IPS. When

acceptable to the gas supplier and local codes, 3/8" approved tubing may be used for lengths under 20 ft (6.1 m). For lengths over 20 ft (6.1 m), larger

tubing should be used. Pipe-joint compounds resistant to the action of L.P. gas must be used. An individual manual shutoff valve must be installed

within 6 ft (1.8 m) of the dryer in accordance with the National Fuel Gas Code ANSI Z223.1.

ELECTRICAL REQUIREMENTS

A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required. A time-delay fuse or circuit breaker and a separate circuit

are recommended.

WATER (STEAM MODELS ONLY) REQUIREMENTS

The dryer must be connected to the cold water faucet using new inlet hoses. Do not use old hoses. Do not overtighten.

Damage to the coupling can result.

VENTING REQUIREMENTS

xhaust venting: Exhaust your dryer to the outside. 4" (102 mm)

diameter vent is required. Rigid or flexible metal exhaust vent

must be used. Do not use plastic or metal foil vet. Exhaust hood

must be at least 12" (305 mm) from the ground or any object that

may be in the path of the exhaust.

Exhaust hoods:

Recommended Styles:

Louvered Hood

Acceptable Style:

Angled Hood

Determine vent path:

Select route that will provide straightest and most direct

■

path outdoors.

Plan installation to use fewest number of elbows and turns.

■

When using elbows or making turns, allow as much room

■

as possible.

Bend vent gradually to avoid kinking.

■

Use as few 90° turns as possible.

■

Determine vent length and elbows needed for best

drying performance:

Use following Vent System Chart to determine type of vent

■

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified

in Vent System Chart. Exhaust systems longer than those

specified will:

Shorten life of dryer.

■

Reduce performance, resulting in longer drying times

■

and increased energy usage.

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Box Hood

The "Vent System Charts" provide venting requirements that

will help achieve best drying performance.

Standard Vent System Chart

Number of

Type

90° elbows

of vent

Rigid metal

Long Vent System Chart*

Number of

Type

90° elbows

of vent

Rigid metal

*For Model WGD9051Y only.

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add

one 90° turn to the chart.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Box/louvered

Angled

hoods

58 ft. (17.7 m)

64 ft. (20 m)

54 ft. (16.5 m)

48 ft. (14.6 m)

44 ft. (13.4 m)

38 ft. (11.6 m)

35 ft. (10.7 m)

29 ft. (8.8 m)

27 ft. (8.2 m)

21 ft. (6.4 m)

Box/louvered

Angled

hoods

129 ft. (39.3 m)

130 ft. (39.6 m)

125 ft. (38.1 m)

119 ft. (36.3 m)

115 ft. (35.1 m)

109 ft. (33.2 m)

106 ft. (32.3 m)

100 ft. (30.5 m)

98 ft. (29.9 m)

92 ft. (28.0 m)