Whirlpool 30 " Eye-Level Gas Range Manual de instruções de instalação - Página 3

Imprimir página

Electrical requirements

WARNING

Electrical Shock Hazard

Electrically ground oven.

Connect ground with 10-gauge-

minimum solid copper wire.

Failure to follow these instructions

could result in death, fire or electrical

shock.

If codes permit and a separate ground wire is

used, it is recommended that a qualified

electrician determine that the ground path

and wire gauge are in accordance with local

codes.

Installation Steps

Preparation

WARNING

Excessive Weight Hazard

Use two or more people to move

and install oven.

Failure to follow this instruction can

result in back or other injury.

Important: Use both hands to remove oven

doors.

Do Not use handle or any portion of the

front frame or trim for lifting.

Before moving oven across floor, check that

oven is on shipping base or slide oven onto

cardboard or hardboard.

Do Not remove shipping feet at the front

lower corners of oven.

Do Not

remove

shipping feet.

Turn power supply off. Move oven

close to final position.

• Remove and discard shipping materials,

tape and protective film from the oven.

Do Not remove shipping base or shipping

feet at the front lower corners of oven.

The shipping feet will protect the lower

oven trim until oven is inserted into

cabinet.

• Remove and set aside racks and other

parts from inside oven.

Page 2

Do Not ground to a gas pipe.

Check with a qualified electrician if you are

not sure oven is properly grounded.

Do Not have a fuse in the neutral or ground

circuit.

Oven must be connected to the proper

electrical voltage and frequency as specified

on the model/serial rating plate. (The

model/serial rating plate is located on the

oven door or on the oven frame.)

CONNECT WITH COPPER WIRE ONLY.

Models rated from 7.3 to 9.6 kW at 240

volts (5.5 to 7.2 kW at 208 volts) require a

separate 40-ampere circuit. Models rated

at 7.2 kW and below at 240 volts (5.4 kW

and below at 208 volts) require a separate

30-ampere circuit.

A time-delay fuse or circuit breaker is

recommended.

Remove

side trim

pieces.

Grasp oven frame

to lift oven.

power

supply cable

shipping

foot

Completely open lower oven door.

Insert small end of a door removal pin into

each door hinge. Grasp door handle from the

bottom and gently close door as far as it will

shut. Lift slightly and grasp bottom of door

with other hand. Pull door out at bottom to

remove. Set door aside on protected surface.

Connect directly to the fused disconnect

(or circuit breaker box) through flexible,

armored or non-metallic sheathed, copper

cable (with ground wire).

Flexible armored cable from appliance

should be connected directly to junction

box.

Fuse both sides of the line.

A U.L.-listed conduit connector must be

provided at the junction box.

Do Not cut the conduit.

Wire sizes and connections must conform

with the rating of the appliance and to the

requirements of the National Electrical Code,

ANSI/NFPA 70 — latest edition (*, See Page 1)

or Canadian Electrical Code, C22.1-1982 and

C22.2 No. 01982 (or latest edition) (**, See

Page 1) and all local codes and ordinances.

Remove

oven racks.

Insert small

end of pin

here.

Remove trim screws attaching right

and left side trim to oven. Grasp the bottom

end of trim and pull away from oven. Slide

top end of trim downward to remove trim

from oven. Take care not to scratch other

surfaces with ends of trim. Set trim and

screws aside on protected surface.

Check oven and

microwave oven operation.

Use screws to attach

oven to cabinet.

Reattach side

trim pieces.

Remove

trim screws.

Remove

oven door.

Replace

oven door.

Remove trim screw.

Pull trim out.

Pull top of trim

down.