Whirlpool 30 " Eye-Level Gas Range Manual de instruções de instalação - Página 5

Imprimir página

17³⁄₁₆" (43.7 cm)

*For non-vented (recirculating) installations

**For vented installations

Cabinet Dimensions

10" (25.4 cm) min.

13" (33.0 cm) max.

9¹⁄₂" (24.1 cm)

10" (25.4 cm) min.

13" (33.0 cm) max.

Side

cabinet

30" (76.2 cm) or

36" (91.4 cm)

"X"

bottom of

canopy

to cooking

surface

*For non-vented (recirculating) installations

IMPORTANT:

Minimum distance "X": 24" (61.0 cm) from electric cooking

surface

Minimum distance "X": 27" (68.6 cm) from gas cooking

surface

Suggested maximum distance "X": 36" (91.4 cm)

**27¹⁄₈" (68.9 cm) min.

**41¹⁄₈" (104.5 cm) max.

*27¹⁄₈" (68.9 cm) min.

*45¹⁄₂" (115.6 cm) max.

2" (5.1 cm) min.

9" (22.9 cm) min.*

Vent and power

supply cable

entry location

20" (50.8 cm)* min.

Side

cabinet

Centerline

Cooking surface

The chimneys can be adjusted for different ceiling heights. See

the following chart.

Vented Installations

Min. ceiling height

7' 4" (2.23 m)

Electric cooking

surface

7' 7" (2.31 m)

Gas cooking

surface

Non-vented (recirculating) Installations

Min. ceiling height

7' 4" (2.23 m)

Electric cooking

surface

7' 7" (2.31 m)

Gas cooking

surface

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or soffit heights depending on the

distance "X" between the bottom of the range hood and the

cooking surface. For higher ceilings, a Stainless Steel Chimney

Extension Kit Part Number W10294735 is available from your

dealer or an authorized parts distributor. The chimney extension

replaces the upper chimney shipped with the range hood.

Venting Requirements

(vented models only)

Vent system must terminate to the outdoors, except for non-

vented (recirculating) installations.

Do not terminate the vent system in an attic or other enclosed

area.

Do not use 4" (10.2 cm) laundry-type wall cap.

Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

Use no more than three 90° elbows.

Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

Do not install 2 elbows together.

Use clamps to seal all joints in the vent system.

The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

Use caulking to seal exterior wall or roof opening around the

cap.

The size of the vent should be uniform.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale. Consult

your HVAC professional for specific requirements in your area.

Max. ceiling height

9' 5" (2.87 m)

Max. ceiling height

9' 9" (2.97 m)