L.P. gas conversion
IMPORTANT: All connections
must be
wrench-tightened.
Do Not make
connections
to the gas regulator
too tight.
Making
the connection
too tight may crack
the regulator
and cause a gas leak. Do Not
allow the regulator
to turn on the pipe
when tightening
fittings.
1.P. posltion
\
Natural
gas position
\
Converting back to Natural gas
1. Convert
the pressure regulator
back to
Natural
gas by reversing
the steps in Step
A, "Pressure regulator".
2. Remove
screw located
in center
of each
burner. Remove
LP air shutters from
burners. Replace
screws. Save the L-Pair
shutters,
3. Remove
L.F?gas orifices (No. 93) and
save. Install Natural
gas orifices (No. 155).
Adjusting for proper flame
After all burners have been converted,
turn
the gas supply valve back to open
position.
Complete
steps 9-l 5.
2. Remove
cover from cap on top of
regulator,
Turn cap over so that L.F! is on
top of cap. Replace
cap. Replace
cover
over cap.
Electrical
Shock Hazard
Disconnect
power before converting
to
L.P. gas.
Failure to do so can result in death or
electrical
shock.
Checking
gas pressure
1. Remove
right rear burner
cap. Connect
an inclined
manometer
to orifice with a
l/4" I.D. rubber
hose. Hold hose tightly
to
orifice.
2. Turn two other burners to operate
at the
'HI" position. Turn on burner
connected
to the manometer,
Adjust the gas supply
pressure until the monometer
pressure
reading
is one-inch
water
column
above
4 for Natural
gas and 10 for L.F?gas
pressure. The gas pressure should never
be set below
4 or above
14 inches for
Natural
gas and below
10 or above
14
for L.P gas.
gasket
Converting
to L.F! gas should
be done by a
qualified
installer.
Important:
Observe
all governing
codes
and ordinances.
Failure to meet codes and ordinances
could
result in risk of fire or electrical
shock.
Tools and materials
needed for
installation.
3. Remove cap from top of regulator,
Snap
out plastic plunger
from bottom
of cap.
Turn plunger
over so that L-f? is shown on
lower end of plunger
and snap back into
cap.
Wiring diagram
N-
TOP IGNITORS
TOP
BURNER
IGNITION
SWITCHES
L.F! gas-resistant
pipe-joint
compound
m
,
m-))
7mm nut driver
1. Use nut driver to remove
Natural gas
orifices (marked
No. 155). Set orifices
aside.
2. Remove
L.P orifices (marked
No. 93) from
plastic bag attached
to bottom
of
cooktop.
Use nut driver to install L.l?gas
orifices,
Parts supplied for
installation.
burner cap
xz)]
l
4 L.F! alr shutters
l
4
L.P. gas orifices
l
4
screws
SCHEMATIC
Converting to 1-P. gas
Complete
steps l-8 before
converting
your
cooktop
to LPgas.
screw -
L
TOP
BURNER
IGNITION
SWITCHES
.
B-
air shutter (used
with L.F? gas only)
BLK
BLK BLK
BLK
A
w
Pressure regulator:
The pressure
regulator
may be one of three types. Follow
instructions
that apply
to your type of
regulator.
3. Remove screw located
in center
of each
burner. Remove
L.P air shutters from
plastic bag attached
to bottom
of
cooktop.
Install L.P air shutters. Replace
screws.
4. Save the Natural gas orifices (No. 155),
should the cooktop
need to be
converted
back to Natural
gas.
NOTICE:
1. DISCONNECT
RANGE FROM POWER
BEFORE REMOVING WIRE COVER.
2. REFER ONLY TO FEATURES
EQUIPPED.
3. SERVICER
PLEASE RETURN DIAGRAM
TO RANGE.
1. Push down
and turn cap counterclockwise
to remove
cap. Turn cap over so that L.P is
on top of cap. Replace
cap.
Panel E
Imprimir página