Whirlpool RH2000 Series Instruções de instalação - Página 4

Procurar online ou descarregar pdf Instruções de instalação para Campânula de ventilação Whirlpool RH2000 Series. Whirlpool RH2000 Series 5 páginas. 30" vented custom series range hood
Também para Whirlpool RH2000 Series: Instruções de instalação (5 páginas), Instruções de instalação e manual de utilização e cuidados (7 páginas), Instruções de instalação (5 páginas)

Imprimir página

5-3/4"

6-1/4"

7-1/8"

To vent through the roof or wall, mark 5-3/4"

and 6-1/4" in from back wall along the

centerline on underside of cabinet. Use

these points as centers to draw 7-1/8"

circles on underside of cabinet.

Use a saber saw to cut the openings for the

vent system. Repeat for the underside of

the top of the cabinet. This will create

slotted openings which makes it easier to

install the vent system..

Install vent system through the vent

opening in upper cabinet or wall.

Complete venting system according to

method needed. See "Venting

requirements." Use caulking to seal exterior

wall or roof opening.

10.

If roof or wall cap does not

have a damper, install damper

(supplied with hood) in vent system to

prevent air from flowing back into vent

system.

If roof or wall cap has a damper, Do Not use

damper blade supplied with range hood.

11.

Do Not turn on power until

installation is complete. Run

wiring through wall or cabinets according

to the National Electrical Code and local

codes and ordinances. Use caulking to seal

ceiling or outside wall opening.

12.

Start screws in the center of the

narrow neck of each of the

four keyhole mounting screw slots marked

on the cabinet bottom.

keyhole slot

13.

Lift range hood into final

position, feeding electrical wire

through wiring opening. Tighten mounting

screws to cabinet, making sure mounting

screws are in narrow neck of slot.

WARNING

Electrical Shock Hazard

Disconnect power before making

electrical connections.

Connect ground wire to green ground

screw in terminal box.

Failure to do so can result in death or

electrical shock.

Panel C

cabinet

cutouts

14.

For models requiring direct wiring:

Connect the white and black wires of the

power supply cable to the white and black

leads in the range hood with twist-on

connectors.

Connect the power supply grounding wire

to the green, grounding screw inside the

range hood terminal box.

Use caulking to seal wire opening.

Replace terminal box cover.

For cord connected models:

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can

result in death, fire, or electrical shock.

For your personal safety, this range hood

must be grounded. To minimize possible

shock hazard, the cord must be plugged

into a mating, 3-prong, ground-type outlet,

grounded in accordance with National

Electrical Code, ANSI/NFPA 70 – latest

edition* and all local codes and

ordinances.

If mating outlet is not available, it is the

responsibility and obligation of the customer

to have a properly grounded, 3-prong

outlet installed by a qualified electrician.

Do not use an extension cord.

Using a U.L.-listed power supply

cord-connection kit:

Follow Power Cord Kit instructions for

connecting wiring.

Check that

screw is in

narrow neck

Replace terminal box cover.

of slot.

For models with a factory installed

front of hood

power cord:

Plug power cord into grounded 3-prong

screw

outlet.

15.

Copies of standards listed may be obtained from:

* National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

Congratulations!

black

white

green

ground

screw

ground

wire

WARNING

Electrical Shock Hazard

Turn power supply on.

You have just

finished installing

your new range hood.

Keep Installation Instructions

close to range hood for easy

reference. The instructions will

make reinstalling your

range hood in another home

as easy as the first

installation.

Operation

of range hood

For best results, turn range hood fan ON at

beginning of cooking and allow it to run

until all smoke and odors are removed from

room.

To turn fan ON and OFF:

Press fan control to turn fan on and off and

adjust fan speed. Speed may be increased

or decreased anytime during range hood

operation.

To turn range hood light ON and OFF:

Press light control to turn light on or off. Light

may be turned off or on anytime during

range hood operation.

Care of

range hood

Filter/light lens:

For best results, remove and clean often.

To remove filter/light lens:

filter tab

Pull firmly on filter tab to remove filter/light

lens from range hood..

To clean filter/light lens:

Place filter/light lens in dishwasher or hot

sudsy water to clean.

To reinstall filter/light lens:

Place edge of filter/light lens in opening so

that right side is above flange and tab

faces downward. Press filter/light lens into

position.

When it's time to replace your

aluminum filter/light lens:

1. Model series RH2000X:.

Order Filter/Light Lens no. 883149

2. Call Whirlpool's Telesales line at

1-800-442-9991

3. Give the Telesales Representative the

part number needed.

4. The Representative will give you the

current price.

5. Place your order using your Master

Card

, Visa

or Discover

6. If you wish: mail a check or money order

to:

Whirlpool Corporation

1900 Whirlpool Drive

LaPorte, IN 46350-9980

Attn: Accessory Accounting

7. Be sure to ask the Telesales

Representative about the wide variety of

other Whirlpool Product Accessories.

To clean fan motor:

Every three years lubricate each motor

bearing with a few drops of oil to help

prolong motor life.

Clean exterior of motor with a damp cloth

and grease-cutting detergent.

Exterior surfaces

Clean the range hood with a mild

detergent and soft cloth. Do Not use

abrasive cleansers or steel wool pads.

Light

Do Not use bulb larger than 60 watts in light

socket.

Light bulb is not included.

credit card.