Whirlpool RH2636XJQ2 Instruções de instalação e manual de utilização e cuidados - Página 5
Procurar online ou descarregar pdf Instruções de instalação e manual de utilização e cuidados para Campânula de ventilação Whirlpool RH2636XJQ2. Whirlpool RH2636XJQ2 7 páginas. 36" range hood (ductless)
Também para Whirlpool RH2636XJQ2: Lista de peças (1 páginas)
Imprimir página
[] Install vent through
the vent
opening
in upper cabinet
or wall,
Complete
venting
system according
to
method
needed,
See "Venting
requirements,"
Use caulking
to seal exterior
wall or roof opening,
[] If roof or wall cap does not
have a damper,
attach
rectangular
damper
supplied
with hood to selected
rectangular
vent opening,
If damper
is
attached
to back of range
hood,
be sure
damper
hinge is toward
the top,
If roof or wall cap does not have a damper
and round vent is used, install damper
(supplied
with hood)
in vent to prevent
air
from flowing
back into vent,
If roof or wall cap has a damper,
Do not
use damper
blade
supplied
with range
hood,
[] Do not turn on power
until
installation
is complete.
Run wiring through
wall or cabinets
according
to the National
Electrical
Code
and local codes and
ordinances,
Use caulking
to seal ceiling
or
outside wall opening,
keyhole
slot
front of hood
Check
that screw
is in
narrow
neck of slot.
screw
[] Start screws in the center
of
the narrow
neck of each
of the four
keyhole
mounting
screw slots marked
on
the cabinet
bottom,
[] Lift range hood into final
position,
feeding
electrical
wire through
wiring opening,
Tighten
mounting
screws to
cabinet,
making
sure mounting
screws are
in narrow
neck of slots, ,
Electrical
Shock Hazard
Disconnect power before making
electrical connections.
Connect
ground wire to green ground
screw in terminal
box.
Failure to do so can result in death or
electrical
shock.
white
wire
ground
[]
For models
requiring
direct
wiring:
Connect
the white and black wires of the
power
supply cable
to the white and black
leads in the range
hood with twist-on
connectors,
Connect
the power
supply ground
wire to
the green ground
screw inside the range
hood terminal
box,
Use caulking
to seal wire opening,
Replace
terminal
box cover
Panel
D
For cord
connected
models:
Electrical
Shock Hazard
Plug into a grounded
3-prong outlet.
Do not remove ground
prong.
Do not use an adapter.
Failure to follow these instructions can
result in death, fire, or electrical
shock.
For your personal
safety, this range hood
must be grounded,
To minimize
possible
shock hazard, the cord must be plugged
into a mating,
3-prong,
ground-type
outlet,
grounded
in accordance
with National
Electrical
Code, ANSI/NFPA 70 - latest
edition*
and all local codes
and
ordinances,
If mating
outlet is not available,
it is the
responsibility
and obligation
of the
customer
to have a properly
grounded,
3-
prong outlet installed
by a qualified
electrician,
Do not use an extension
cord,
Using a U.L.-listed
power supply
cord-connection
kit:
Follow Power Cord Kit instructions for
connecting
wiring.
Replace
terminal
box cover,
For models
with a factory
installed power
cord:
Plug power
cord into grounded
3-prong
outlet,
[] Remove
knockout
from the
wiring opening
(rear or top) to be used,
The range hood cabinet
may have venting
knockouts,
Do not remove
these venting
knockouts.
The model
cannot
be vented,
X
terminal
/
cover
[] If your model
does NOT have a
factory
installed power
cord, remove
terminal
box cover on range hood,
Excessive
Weight Hazard
Use two or more people to move and
install range hood.
Failure to follow this instruction can
result in back or other injury.
front of hood
keyhol_
[] Lift range hood into final
position and center,
Mark on underside
of
cabinet
the location
for the four keyhole
mounting
slots, Set range
hood aside on a
protected
surface,
f
centerline
a
[] Determine
and clearly
mark a
vertical
centerline
in the cabinet
opening,
)11
I
I
'11
I
L I
i I
I ,
I
'1
I
II
I
I
wall
cabinet
frame)
centerline
a
[]To wire through
top, mark a line
7-1/2" from the right of the centerline
on
the underside
of the cabinet,
Mark the
point on this line that is 2" from the back
wall, Drill a 1-1/4" diameter
hole through
cabinet
at this point, Note: If a cord-
connection
kit is used, drill a 1-5/8"
diameter
hole,
I
'11
L
I
l-
i
i
3/4"
I
i 7-112"
65-1/4"
I
(to floor)
i
i
i
i
i
i
centerline
I
/
Ii
i
I
To wire through
rear, mark a line 7-1/2" from
the right of the centerline
on the wall, Mark
the point on this line that is 65-1/4" from the
floor (or 3/4" from underside
of cabinet),
Drill a 1-1/4" diameter
hole through
wall at
this point,
Do not turn on power
until
installation is complete.
Use caulking
to seal
ceiling
or outside wall opening,
Run wiring
through
wall or cabinets
according
to the
National
Electrical
Code
and local codes
and ordinances,
keyhole
slot
Check
that screw
is in
narrow
neck of slot.
front of hood
g
a
[] Start screws in the center
of the
narrow
neck of each
of the four keyhole
mounting
screw slots marked
on the
cabinet
bottom,
[] Lift range hood into final
position,
feeding
electrical
wire through
wiring opening,
Tighten
mounting
screws to
cabinet,
making
sure mounting
screws are in
narrow
neck of slots,