Bad Boy 48721201 Manual do operador - Página 6
Procurar online ou descarregar pdf Manual do operador para Cortador de relva Bad Boy 48721201. Bad Boy 48721201 20 páginas.
Imprimir páginaNOTE: Before continuing installation, you must install
the Bad Boy Pup Series bolt-on hitch P#(093-1112-00)
for the rear of the mower. Adding this hitch is required for
mounting the collection system. Contact Bad Boy to
purchase at (870) 698-0090.
2-2 Left Lower Frame Leg Installation
Remove the (2) existing bolts and nuts from the left side
that fastens the mower's rear frame to the mower's
chassis. Align the (2) lower holes on the left lower frame
leg P#(B0182) (Figure 2) to the (2) lower holes on the
mower's rear frame. Fasten by using (2) 5/16"-18 x 1-
1/4" Grade 8 HHCS P#(K0118) and (2) 5/16"-18 flange
nuts P#(K1178). Once the frame leg is fastened, drill a
hole into the mower's rear frame by using the frame leg
as a pilot and using a 5/16" drill bit. Fasten by using (1)
5/16"-18 x 1-1/4" Grade 8 HHCs P#(K0118) and (1)
5/16"-18 flange nut P#(K1178). Tighten all nuts and
bolts.
Figure 2.
Left Lower
Frame Leg
Fasten Lower
Frame Leg w/
(2) 5/16" x 1-1/4"
G8 HHCS
(2) 5/16" Flange Nuts
2-3 PTO Assembly Installation
Remove the (2) existing bolts and nuts from the right
side that fastens the mower's rear frame to the mower's
chassis. Align the (2) lower holes on the PTO assembly
P#(A0610) (Figure 3) to the (2) lower holes on the
mower's rear frame. Fasten by using (2) 5/16"-18 x 1-
1/4" Grade 8 HHCS P#(K0118) and (2) 5/16"-18 flange
nuts P#(K1178). Once the PTO assembly is fastened,
drill a hole into the mower's rear frame by using the PTO
assembly as a pilot and using a 5/16" drill bit. Fasten by
using (1) 5/16"-18 x 1-1/4" Grade 8 HHCS P#(K0118)
and (1) 5/16"-18 flange nut P#(K1178). Tighten all nuts
and bolts.
Drill Hole Here
Fasten w/
(1) 5/16" x 1-1/4"
G8 HHCS
(1) 5/16" Flange Nut
Mower
Rear
Frame
Figure 3.
Fasten Lower PTO Assembly w/
(2) 5/16" x 1-1/4" G8 HHCS
(2) 5/16" Flange Nuts
2-4 Belt Installation
Remove the pulley guard P#(B0075) by removing the (2)
1/4"-20 x ½" HHSTS P#(K0353), see page 10, diagram #
38 and #39 for part location. Loosen the (2) bolts that
secure the gear box assembly P#(A0429) to the PTO
mount plate (Figure 4). Loosen the adjustment bolt
P#(K0348) until the gear box assembly is at the far left
adjustment (the gear box is moved towards the mower's
engine pulley). Connect the kevlar cord belt from the
engine pulley to the lower gear box pulley (Figure 5).
To tension the drive belt, turn the adjustment bolt
clockwise until there is 1" of deflection, with 10-11 lbs. of
pressure between the engine pulley and the gear box
pulley. Once the correct tension of the belt is achieved,
tighten the (2) bolts that secure the gear box assembly.
Figure 4.
6
Drill Hole Here & Fasten w/
(1) 5/16" x 1-1/4" G8 HHCS
(1) 5/16" Flange Nut
Mower Rear Frame
PTO Assembly
Loosen Gear Box Bolts
Adjustment Bolt
PTO Mount Plate